Operators Manual
Table Of Contents
- Vibroplate
- Foreword 3
- 1. Emission System Control Information 4
- 2. Safety Information 5
- 3. Technical Data 15
- 4. Operation 18
- 5. Maintenance 23
- 5.1 Periodic Maintenance Schedule 23
- 5.2 Cleaning Plate 25
- 5.3 Drive Belt 25
- 5.4 Exciter Lubrication 26
- 5.5 Spark Plug 27
- 5.6 Engine Oil 28
- 5.7 Air Cleaner 29
- 5.8 Cleaning Sediment Cup 30
- 5.9 Adjusting Engine Speed 30
- 5.10 Carburetor Adjustment 31
- 5.11 Troubleshooting 32
- 5.12 Storage 33
- 5.13 Lifting Machine 34
- 5.14 Transporting Machine 35
- Foreword
- 7.1 Emission Control Systems Warranty Statement
- 2. Safety Information
- 2.1 Laws Pertaining to Spark Arresters
- 2.2 Operating Safety
- 2.3 Operator Safety while using Internal Combustion Engines
- 2.4 Service Safety
- 2.5 Label Locations
- 2.6 Warning and Informational Labels
- 2.7 Operating Labels
- 3. Technical Data
- 3.1 Engine Data
- 3.2 Machine Data
- 3.3 Sound and Vibration Specifications
- 3.4 Dimensions
- 4. Operation
- 4.1 Recommended Fuel
- 4.2 Before Starting
- 4.3 To Start
- 4.4 To Stop
- 4.5 Application
- 4.6 Operation
- 4.7 Wheel Kit (0162986)
- 5. Maintenance
- 5.1 Periodic Maintenance Schedule
- 5.2 Machine Maintenance
- 5.3 Cleaning Plate
- 5.4 Drive Belt
- 5.5 Exciter Lubrication
- 5.6 Spark Plug
- 5.7 Engine Oil
- 5.8 Air Cleaner
- 5.9 Cleaning Sediment Cup
- 5.10 Adjusting Engine Speed
- 5.11 Carburetor Adjustment
- 5.12 Troubleshooting
- 5.13 Storage
- 5.14 Lifting Machine
- 5.15 Transporting Machine
- Blank Page
WP 1540A/AW Maintenance
wpm_tx001130gb.fm 25
5.3 Cleaning Plate
Clean plate after use to remove dirt, stones, and mud caught under the
engine console. If plate is being used in a dusty area, check engine
cylinder cooling fins for heavy dirt accumulation. Keep engine cylinder
fins clean to prevent engine from overheating.
5.4 Drive Belt
See Graphic: wc_gr000077
On new machines or after installing a new belt, check belt tension after
first 20 hours of operation. Check and adjust belt every 50 hours
thereafter.
To change the belt:
5.4.1 Remove the beltguard and remove the four hex nuts (a) holding pulley
halves (b) together. Remove outer pulley half and remove belt.
5.4.2 Install new belt on pulley and secure pulley halves together with hex
nuts. Adjust tension on belt by adding or removing spacers (c)
between pulley halves. The fewer spacers used between pulley
halves, the tighter the belt will be. Three spacers with new Wacker
belts should provide the correct tension. Belt deflection should be 6–
10 mm, checked half way between the clutch pulley and the exciter
pulley (d). Place unused spacers on outside of pulley.
5.4.3 Replace beltguard.
w c _ g r 0 0 0 0 7
7
=
>
?
@