Machine configuration manual Vibratory plate DPU 130Le 08.
Manufacturer Wacker Neuson Produktion GmbH & Co. KG Preußenstraße 41 80809 München www.wackerneuson.com Tel.
DPU 130 1 Foreword .................................................................................................................... 4 2 Introduction ............................................................................................................... 5 2.1 2.2 3 Means of representation for this operator's manual....................................................... 5 Wacker Neuson representative......................................................................................
1 Foreword 1 DPU 130 Foreword Purpose of this manual This manual describes the possible settings and the use of the configuration menu on the machine's display screen. This manual also contains the factory-set PIN data of your machine. This manual is only intended for the operator of the machine, not for the user. Store this manual where it will be safe from unauthorized access.
2 Introduction 2 2.1 Introduction Means of representation for this operator's manual Warning symbols This operator's manual contains safety information of the categories: DANGER, WARNING, CAUTION, NOTICE. They should be followed to prevent danger to life and limb of the operator or damage to equipment and exclude improper service. DANGER This warning notice indicates immediate hazards that result in serious injury or even death. f Danger can be avoided by the following the actions mentioned.
2 Introduction Instructions f This symbol indicates there is something for you to do. 1. Numbered instructions indicate that you have to carry out something in a defined sequence. 2.2 This symbol is used for lists. Wacker Neuson representative Depending on your country, your Wacker Neuson representative is your Wacker Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer. You can find the addresses in the Internet at www.wackerneuson.com.
DPU 130 3 3 Using the configuration menu Using the configuration menu The machine has a machine configuration system, with which you can adjust certain of the machine's settings to meet your requirements: Item Designation 1 Configuration menu 2 Remote control Settings options in the configuration menu In the configuration menu on the display screen, you can adjust the following machine settings: Change setup PIN. Modify/activate/deactivate machine PIN. Set machine turn-off time.
3 Using the configuration menu 3.1 DPU 130 Opening the configuration menu and changing settings CAUTION Unintentional changing of settings. If you select Setup Exit, the changed settings are always saved. f If you accidentally changed settings and you do not want to save them, switch off the machine with the emergency stop switch. Opening the configuration menu Note: Item Access to the configuration menu is secured by the setup PIN.
DPU 130 3 Using the configuration menu After approx. 2 seconds the following text appears on the display: Setup-PIN Enter PIN 4. If the following text appears on the display, enter the setup PIN using the remote control and then press the ON/OFF switch on the machine. Enter PIN 0000 Push the left control lever on the remote control forward or backward to select the position. Push the right control lever on the remote control forward or backward to select the number.
3 Using the configuration menu DPU 130 Changing the setup PIN The setup PIN secures access to the configuration menu. You can change the factory default setup PIN. Note: Never deactivate the setup PIN because otherwise the configuration menu is not protected against unauthorized changes. 1. Press the ON/OFF switch on the machine until the following text appears on the display: Setup Setup-PIN 2. After approx.
DPU 130 3 Using the configuration menu Changing the PIN You can set a PIN that will protect the machine from unauthorized operation. After activating the machine, the user must enter the PIN with the remote control. 1. Press the ON/OFF switch on the machine until the following text appears on the display: Setup PIN 2. After approx.
3 Using the configuration menu DPU 130 Setting the turn-off time You can select the amount of time after which the machine automatically deactivates if it does not receive any more commands from the remote control. 1. Press the ON/OFF switch on the machine until the following text appears on the display: Setup Turn-off time 2. After approx.
DPU 130 3 Using the configuration menu Setting the language You can choose the language in which information will be shown on the display screen. 1. Press the ON/OFF switch on the machine until the following text appears on the display screen: Setup Select language 2. After approx. 2 seconds the following text appears on the display and you can set the language: Select language 1 Push the right control lever on the remote control forward or backward to select the number.
3 Using the configuration menu DPU 130 Setting the overload sensor The machine's overload sensor detects when you are operating the machine on hard ground that cannot be further compressed. You can determine how the machine should react to overload in order to protect it from damage. 1. Press the ON/OFF switch on the machine until the following text appears on the display: Setup Overload sensor 2. After approx.
DPU 130 3 Using the configuration menu Exiting the configuration menu and saving your settings 1. Press the ON/OFF switch on the machine until the following text appears on the display screen: Setup Exit After approx. 2 seconds the changed settings are saved and the configuration menu is exited. Note: If you are uncertain and wish to check the changed settings again, before the 2 seconds have elapsed, press the ON/OFF switch on the machine to run through the configuration menu again. 2.
3 Using the configuration menu 3.2 DPU 130 Changing from numerical code display to language display Note: The meaning of the numerical codes is given in the appendix of the operator's manual. The following steps are necessary to switch from numerical code display back to language display: 1. Activate machine. 2. Turn on remote control. 3. Hold the ON/OFF switch on the machine at the same time as the Stand vibration button on the remote control for at least 3 seconds. 4.
DPU 130 3 Using the configuration menu Value Language 0 German (factory default setting for EU machines) 1 English (factory default setting for US machines) 2 French 3 Spanish 4 Numerical code display (no language) Language-neutral display solely using numerical code. Use this setting if the user does not understand the languages listed above. The meaning of the numerical codes is given in the appendix of the operator's manual. 7.
4 Troubleshooting 4 DPU 130 Troubleshooting Potential faults, their causes and remedies can be found in the following table. 18 Malfunction Cause Remedy Configuration menu cannot be called. Machine has not been activated. Activate machine and wait until the display screen shows the hours of operation. The ON/OFF switch on the machine and on the remote control was not pressed down for long enough.
DPU 130 5 5 PIN data PIN data The following table contains the factory-default PIN data: f Note the modified PIN data in the following table: Machine no. PIN Setup PIN 0000 (PIN request deactivated) Note: Modified by 8946 Date Factory default setting If you have forgotten the PIN, you can also unlock the machine with the setup PIN.
5 PIN data 20 DPU 130 Machine configuration manual
