Instruction manual

Before rst use 4
4.1 Scope of delivery
1 LED-ashlight
3 1.5V batteries, type LR03/AAA
1 Instruction manual
1 Carrying bag
1 Diusor
4.2 Unpacking and checking
1. Carefully remove the device and the accessories from packaging.
2. Remove all packaging materials, and foils, as well as protective foils.
3. Check the contents for completeness and damage. Should the contents not be complete or should there be
detectable damage, do not put device into operation. Return it to the trader immediately.
4. If you want to dispose of packaging material, please observe the legal requirements.
5. Keep the packaging material if you want to wrap the device in it, ship or transport it in any other way. Store it
in a way that it does not present any risk potential.
Caution - choking hazard! Packaging material is not a toy. Children can choke on plastic bags, foil and
small parts of polystyrene. Therefore, always keep packaging material away from children.
Operating 5
5.1 Inserting/replacing batteries
1. Screw o battery compartment cover (2) with integrated ON/OFF-button from casing in an anti-clockwise
direction.
2. Take o battery holder, remove exhausted batteries if necessary. Clean the device and battery contacts if
required and insert the three provided or other, new batteries of size LR03/AAA 1.5 V.
3. Screw the battery compartment cover (3) back on. Make sure the cover is fully closed.
4. Observe the safety instructions regarding the handling of batteries. (See chapter: Safety instructions)
5. Replace the batteries as soon as light intensity of the device starts ceasing.
5.2 Switching on / o
1. The on-/o-button is located on the battery compartment cover (2) of the device.
2. Push the on-/o-button up to the stop to turn the device on or o.
5.3 Changing the operating mode
1. During operation you can switch between two operating modes by pushing the on-/o-button only halfway
through.
2. Push the on-/o-button up to the stop to turn on the device for the rst time. Maximum power (100%) with
the brightest light beam will be set.
3. Push the on/o-button only halfway through to reduce intensity of the light beam (25%). To go back to maxi-
mum power again, push the on-/o-button only halfway through one more time.
5.4 Zoom mechanism
1. Slide the exible lens attachment (4) to increase or reduce the size of the light beam.
2. If you slide the lens attachment (4) up to the stop, the light will be bundled to a narrow, selective light beam.
The light beam will be very bright and have a very large range. This setting is very suitable for bright illumina-
tion of small areas or for searching objects at a great distance.
3. If you slide the lens attachment (4) back up to the stop, the light beam will be widely scattered. The light
beam will be less bright and will not reach very far. This setting is especially suitable for illumination of larger
areas in the close proximity, e.g. to illuminate the path for a stroll in the dark.
5.5 Function of the diusor
To attach the diusor, simply push it onto the lens attachment of the ashlight. To remove the diusor, simply
take it o the lens attachment again. (See Fig. 1)
By means of the diusor function the light can spread to the surroundings and oers you light similar to that
of a source of illumination! Depending on your needs, the diusor turns your ashlight into a tent lamp, a
reading lamp or into soft all-around lighting.
Cleaning and maintenance 6
6.1 Cleaning and maintenance
1. Clean the device with a lightly dampened cloth and a mild detergent if necessary. Subsequently dry the
device well. Make sure no liquids get into the casing.
2. Do not use scouring or solvent-based agents. Do not use scraping or sharp objects to clean.
3. Never hold the device under running water and do not immerse it in water or other liquids.
4. Clean lens with a very soft cloth to not scratch the surfaces. For stubborn soiling use a little glass cleaner or
rubbing alcohol.
5. While cleaning the lens attachment can be removed. Ensure that sealing washers are correctly inserted before
reapplying the lens attachment.
6. Use the carrying loop (4) to attach the device to a belt or backpack.
6.2 Troubleshooting
In case the device is not working, check the following:
1 Are batteries inserted into the device?
2 Are batteries inserted with the correct polarity (+/-)?
Insert 3 batteries of type LR03/AAA into the battery compartment and observe the correct
polarity (+/-) according to imprint.
Should you not be able to solve a problem by following the above-mentioned information, call on our customer
service. Do not try repairing the device yourself by any means.
Disposal 7
This symbol refers to the fact that electronic devices must not be disposed of with the normal house-
hold waste within the EU.
Please use return and collection points in your municipality or turn to this product‘s point of sale
where you bought it.
Please dispose of batteries environmentally appropriate. Do not discard them into the household
waste. Please use return and collection points in your municipality or turn this product‘s point of sale
where you bought it.
JTM Contracts, Picktree court
Picktree Lane, Chester Le Street
County Durham, DH3 3SY
For UK customers: Phone [phone]
For IR customers: Phone [phone]
This instruction manual also may be downloaded at www.wachsmuth-krogmann.com