Installation & Assembly

ManualsBrandsWAC Lighting ManualsCeiling Lights120V W Track

1

2

3

4

5

6

7

8

9

WAC Lighting

www.waclighting.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2014

INSTALLATION INSTRUCTION

W Track Surface Mount 120V

WT4, WT8, WT12

SAFETY INSTRUCTION

IMPORTANT: NEVER attempt any work without shutting o the electricity.

• Read all of these instructions before installing the track system.

• Turn o power at main switch before installing or modifying the system.

• Do not install within 6 inches of any curtain or combustible materials.

• Do not install less than 5 feet above a oor.

• Do not install in damp or wet locations.

• Do not install concealed, or extended through building walls.

• Do not attempt to energize anything other than a track light xture.

• Do not connect a track to more than one branch circuit. Although track light system may seem to operate acceptably,

a dangerous overload of the neutral may occur and result in a risk of re.

• Check with a qualied electrician before wiring.

• All of the installations shall be in accordance with NEC and all local codes.

• Save these installation instructions and refer to them when additions or changes to the track conguration are made.

MOUNTING OPTIONS

A: Surface Mount

• Mounting slots can be knocked out and are spaced

every 12 inches for convenience.

• Mount track ush to the surface and

secure screws (included).

B: TOGGLE BOLT MOUNT

• Mounting slots can be knocked out and are

spaced every 12 inches for convenience.

• Hang track from the surface using toggle bolts

(included).

MOUNTING OPTIONS

A: Surface Mount

• Mounting slots can be knocked out and are spaced

every 12 inches for convenience.

• Mount track ush to the surface and

secure screws (included).

Summary of content (14 pages)

PAGE 1
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all of these instructions before installing the track system. • Turn off power at main switch before installing or modifying the system. • Do not install within 6 inches of any curtain or combustible materials. • Do not install less than 5 feet above a floor. • Do not install in damp or wet locations.
PAGE 2
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 FEED OPTIONS • Make sure power is off before wiring. • Note the polarity indicator of the track and accessories. Live End Connector (WEDL / WEDR) 1. Slide live end connector into track and secured screw (Fig 4a). 2. Remove the cover. 3. Bring feed through either the knock-out on the bottom of the connector or on the side of the connector (Fig 4b). 4.
PAGE 3
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 L CONNECTER (WLLC / WRLC) WLLC (EARTH CONNECT INSIDE) WRLC (EARTH CONNECT INSIDE) T CONNECTER (WLTC / WRTC) WLTC (EARTH CONNECT LEFT) WRTC (EARTH CONNECT RIGHT) WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.
PAGE 4
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 X CONNECTER (WXC) WXC I CONNECTER (WIC) WIC FLEXIBLE CONNECTER (WFC) WFC WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050 Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.
PAGE 5
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 ACCESSORY OPTIONS • Make sure power is off before connecting. • Note the polarity indicator of the track and accessories. The I Power Connector (WPC) must be placed directly between two track sections as shown in Fig 5 before securing the screw. FIG 5: WPC INSTALLATION End Caps (WEC) should be inserted into the track and secured as shown in Fig 6.
PAGE 6
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 MAXIMUM LOAD The drawings (Fig 8a, Fig 8b, Fig 8c) show the maximum permissible mechanical load by 2-circuit W2 tracks for luminaires or other loads in relationship to the fixation or suspension point. It includes both of the weights of the track system. FIG 8A: MAXIMUM LOAD - 1 FIG 8B: MAXIMUM LOAD - 2 FIG 8C: MAXIMUM LOAD - 3 WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.
PAGE 7
INSTALLATION INSTRUCTION W Track Surface Mount 120V WT4, WT8, WT12 TRACK HEAD OPTIONS W2 LINE VOLTAGE / CFL TRACK HEAD 1. Set circuit selector to 0. 2. Set locking arm to unlock position. 3. Align this tab to the slot on the track (Fig 9a). 4. Insert adapter (Fig 9b, Fig 9c). 5. Set locking arm to lock position. 6. Set circuit selector to 1 or 2. FIG 9A: ADAPTER TO BE INSERTED FIG 9C FIG 9B: INSERTED ADAPTER CONVERTER (CV-2T-LV / CV-2T-MH) FOR J TRACK HEADS 1. J track head insert converter(Fig 10a). 2.
PAGE 8
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 SAFETY INSTRUCTION • Read all of these instructions before installing the track system. • Turn off power at main switch before installing or modifying the system. • Do not install within 6 inches of any curtain or combustible materials. • Do not install less than 5 feet above a floor. • Do not install in damp or wet locations. • Do not install concealed, or extended through building walls.
PAGE 9
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 FEED OPTIONS • Make sure power is off before wiring. • Note the polarity indicator of the track and accessories. Live End Connector (WEDL / WEDR) 1. Slide live end connector into track and secured screw (Fig 4a). 2. Remove the cover. 3. Bring feed through either the knock-out on the bottom of the connector or on the side of the connector (Fig 4b). 4.
PAGE 10
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 L CONNECTER (WHLLC / WHRLC) T CONNECTER (WHLTC / WHRTC ) WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050 Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.
PAGE 11
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 X CONNECTER (WHXC) I CONNECTER (WHIC) FLEXIBLE CONNECTER (WHFC) WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive • Port Washington, NY 11050 Phone (516) 515.5000 • Fax (516) 515.5050 Western Distribution Center 1750 Archibald Ave • Ontario, CA 91761 Phone (800) 526.2588 • Fax (800) 526.
PAGE 12
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 ACCESSORY OPTIONS • Make sure power is off before connecting. • Note the polarity indicator of the track and accessories. The I Power Connector (WHPC) must be placed directly between two track sections as shown in Fig 5 before securing the screw. End Caps (WEC) should be inserted into the track and secured as shown in Fig 6. WAC Lighting www.waclighting.com Phone (800) 526.2588 • Fax (800) 526.
PAGE 13
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 MAXIMUM LOAD The drawings (Fig 7a, Fig 7b, Fig 7c) show the maximum permissible mechanical load by 2-circuit W2 tracks for luminaires or other loads in relationship to the fixation or suspension point. It includes both of the weights of the track system. FIG 7A: MAXIMUM LOAD - 1 End Caps (WEC) should be inserted into the track and secured as shown in Fig 6. FIG 7B: MAXIMUM LOAD - 2 FIG 7C: MAXIMUM LOAD - 3 WAC Lighting www.
PAGE 14
INSTALLATION INSTRUCTION W Track Surface Mount 277V WHT4, WHT8, WHT12 TRACK HEAD OPTIONS CFL TRACK HEAD 1. Set circuit selector to 0. 2. Set locking arm to unlock position. 3. Align this tab to the slot on the track (Fig 8a). 4. Insert adapter (Fig 8b, Fig 8c). 5. Set locking arm to lock position. 6. Set circuit selector to 1 or 2. FIG 8A: TO BE INSERTED LOW VOLTAGE AND METAL HALIDE TRACK HEAD 1. Set circuit selector to 0. 2. Set adapter’s locking arm to unlock position. 3.