Installation Sheet

ManualsBrandsWAC Lighting ManualsLightingGemini 1200" 3500K LED Tape Light

INSTALLATION INSTRUCTION

GEMINI 300

T24-GE3

waclighting.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Ave

Ontario, CA 91761

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. January 2022 1.

SAFETY INSTRUCTION

IMPORTANT: NEVER attempt any work without shutting off the electricity.

• Always turn off power at fuse box prior to installation to prevent electrical shock.

• Intended for indoor use. Dry and damp locations.

• For installation and serviced by a qualified, licensed electrician.

• Install in accordance with national electric code, and local regulations.

• Consult with local inspector to assure compliance.

• Do not submerge, or install within 5 feet of a swimming pool.

• Do not connect the tape directly to high voltage power

• Do not exceed maximum run recommended for each tape series

CAUTION – TO REDUCE RISK OF FIRE AND ELECTRICAL SHOCK

• Read all instructions before installing.

• Handle product with care.

• Do not conceal or extend exposed conductors through a building wall

• To reduce the risk of fire and burns, do not install this lighting system where the exposed bare conductors can be shorted or contact any conductive

materials

• To reduce the risk of overheating and potential fire risk, make sure all connections are tight.

• Do not install any fixture assembly closer than 6 in. from any curtain, or similar combustible material.

• Do not modify or disassemble product beyond instructions or warranty will be void.

• Failure to follow safety warnings, and installation instruction will void the warranty

ATTENTION - AFIN DE RÉDUIRE LES RISQUES D'INCENDIE ET DE CHOC ÉLECTRIQUE

• Lire toutes les instructions avant d'installer.

• Manipuler le produit avec soin.

• Ne pas dissimuler et faire passer les conducteurs exposés à travers un mur de bâtiment.

• Afin de réduire les risques d'incendie et de brûlures, ne pas installer ce système d'éclairage là où les conducteurs dénudés peuvent être court-

circuités, ou entrer en contact avec des matériaux conducteurs.

• Afin de réduire le risque de surchauffe et d'incendie potentiel, s'assurer que toutes les connexions sont bien serrées.

• Ne pas installer aucun luminaire à moins de 6 pouces d'un rideau ou d'un matériau combustible similaire.

• Ne pas modifier ou démonter le produit au-delà des instructions sous peine d'annuler la guarantie.

• Ne pas respecter les avertissements de sécurité et des instructions d'installation annulera la garantie.

TROUBLESHOOTING

• If LED is damaged due to bending, folding, twisting or any sharp object, that LED section may not light up. Damaged LED section can be removed by

cutting and reconnecting using Tape to Tape Connector (T24-BS-MM) – Make sure that polarity matches between tapes.

WIRING AND INSTALLATION:

1. Turn Power off at circuit breaker

he maximum allowance distance of wires between the output of power supply and beginning of tape is 25 ft. The minimum output gauge wire

of power supply is 20 AWG.

Do not bend the tape

light on a horizontal

Do not fold or

twist LED Tape

Do not cover LED

tape light with any

Do not power the LED

tape while attached to the

spool or tightly coiled

Avoid contact with

sharp objects

Install on stable

clean, dry surface

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTION GEMINI 300 T24-GE3 SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. • Always turn off power at fuse box prior to installation to prevent electrical shock. • Intended for indoor use. Dry and damp locations. • For installation and serviced by a qualified, licensed electrician. • Install in accordance with national electric code, and local regulations. • Consult with local inspector to assure compliance.
PAGE 2
INSTALLATION INSTRUCTION GEMINI 300 T24-GE3 2.1) Power Supply: PS-24DC-U60R-BT & PS-24DC-U96R-BT To extend the cable length between hard wire power supply or a wiring box to a tape sections, an extension cable (T24-BS-EX2-*) is needed. The extension cable package also provides small screw driver to unscrew the connector. 25ft.
PAGE 3
INSTALLATION INSTRUCTION GEMINI 300 T24-GE3 Joining tape together (If needed), the following accessories can be used to join between tapes section depending on your application: Tape to Tape Connector (T24-BS-MM) – Making sure that voltage polarity connection is match between tapes. Joiner Cable (T24-BS-IC-*) can be used to join between tape sections – the wire insulation jacket shall be stripped. Make sure that voltage polarity connection matches between tapes.
PAGE 4
INSTALLATION INSTRUCTION GEMINI 300 T24-GE3 LED-T-B T24-BS-EX2-* 7. Connect electrical power feed wires to Inline Power to Tape Connector (T24-BS-PM) with tape. Make sure that polarity is correct. The wire insulation jacket shall be stripped. Wire Color waclighting.com Phone (800) 526.2588 Fax (800) 526.
PAGE 5
INSTALLATION INSTRUCTION GEMINI 300 T24-GE3 SYSTEM DIAGRAM: TRIAC / ELV Dimmer Control System: Only PS-24DC-U60R-BT & PS-24DC-U96R-BT ELV Dimmer Control System EN-BT60-24 & EN-BT96-24 can only work with ELV dimmer. waclighting.com Phone (800) 526.2588 Fax (800) 526.