Installation Sheet

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
INSTALLATION INSTRUCTION
LED- LED Picture Light
PL-LED17/ PL-LED23/ PL-LED34
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNT ON 2”x4” SWITCH BOX (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Drill holes in the wall aligned with the key hole located in the mounting plate, insert the plastic anchor (C).
5. Connect the driver’s input wires to switch box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the driver’s ground wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
6. Secure the mounting plate to the switch box using junction box screws fasten it to the wall using wood screw (D). The side of the mounting
plate marked “GND” must face out.
7. Place the fixture on the mounting back plate, and secure it with mounting screw (B).
8. The arm and the lamp head are 180 degree rotatable, rotate them to your desired angel, secure the arm with Allen screw (E) using Allen
wrench (I).
Note: If you want adjust the arm angle, loose the Allen screw (E) first.
OR
MOUNT ON 4”x4”JUNCTION BOX (Fig. 2)
3. Remove the mounting screw (B) from the fixture, and then take down the front cover.
4. Drill holes in the wall aligned with the key hole located in the mounting plate, insert the plastic anchor (C).
5. Connect the driver’s input wires to junction box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet
box has a green and bare copper ground wire, connect the driver’s ground wire to it. Otherwise,connect the driver’s ground wire directly
to back plate using the green screw provided.
6. Secure the mounting ring to the junction box using junction box screws, the side of the mounting plate marked “GND” must face out.
7. Secure the mounting plate and conversion plate (H) to the mounting ring（G） with junction box strew, fasten the mounting back plate to
the wall using wood screw (D).
8. Place the fixture on the mounting back plate, and secure it with mounting screw (B).
9. The arm and the lamp head are 180 degree rotatable, rotate them to your desired angel, secure the arm with Allen screw (E) using Allen
wrench (I).
Note: If you want adjust the arm angle, loose the Allen screw (E) first.
DIMMING WIRING INFORMATION (Fig. 4)
1. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires
information.
2. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
3. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
Back Plate Dimensions:
PL-LED17:16 3/4"
PL-LED23:23 3/4"
PL-LED34:33 3/4"
PL-LED17:14 5/8"
PL-LED23/PL-LED34:17 3/8"
1 3/8"
1 5/8"
PL-LED17/PL-LED23:7"
PL-LED34:8 1/8"
PL-LED17/PL-LED23:5"
PL-LED34:4 1/2"
1 3/8"
1 5/8"
1 3/8"
1 3/4"
Conversion Plate Dimensions: Mounting Ring Dimensions:
Ø4
"
2 5/8"