Specifications

InvisiLED® Classic 24V – Power Supplies And Accessories
POWER SUPPLIES Model # Input Output Dimensions Description
120V AC
Remote Class 2
Transformer
EN2460RB2T
EN24100RB2T
120V
120V
24V/60W
24V/96W
62" × 1s" × 14"
6s" × 1s" × 18"
6’ lead wire included.
Requires a minimum load of 1W.
Max run 60W: 25'
Max run 96W: 40'
120V AC
Plug-in Class 2
AC Transformer
EN2460PART
EN24100PART
120V
120V
24V/60W
24V/96W
2w" × 1s" × 1w"
42" × 1d" × 1w"
6’ lead wire included.
Requires a minimum load of 1W.
Max run 60W: 25'
Max run 96W: 40'
277V DC
Remote Class 2
Transformer
EN24100277R 277V 24V/96W
7d” × 2w” × 1a”
Cannot be dimmed.
Converts 277V to 24V.
Includes 1' input and output wires.
Must use LEDTCEXT144 to extend the
distance between power supply and tape section.
POWER SUPPLY ACCESSORIES Model # Dimensions Description
Wiring box
with switch
TBS
64” × 1s” × 14”
Use when spanning a large gap in a system layout
without leaving exposed wiring (ie: lighting kitchen
cabinets on both sides of a sink or window).
Low voltage wiring is collected inside box,
with Romex® wire output to go behind a wall.
Low Voltage
Wiring Box
LEDTB
12” × w” × d”
Neatly house up to 2 wires.
Lead Wire
LEDTCP2
LEDTCP12
2'
12'
Alternative length of lead wires for plug-in or
remote power supply. May be  eld cut for use
with a remote power supply.
Extension Cable
LEDTCEXT144 12' Use to extend the distance between power supply
and tape section.
TAPE LIGHT ACCESSORIES Model # Dimensions Description
Joiner Cable
LEDTCIC2
LEDTCIC6
LEDTCIC12
LEDTCIC36
LEDTCIC72
2"
6"
12"
36"
72"
Use between tape sections.
4-Way "X"
Connector
LEDTCX
3w” × 3w” × c”
center: w”
arms: 12” each
"X" connector has one male and
three female connectors.
(Total run length power consumption cannot exceed
transformer load when "X" connector is used).
3-Way "Y"
Connector
LEDTCY
3z” × 3z” × c”
center: w”
arms: 12” each
"Y" connector has one male and
two female connectors.
(Total run length power consumption cannot exceed
transformer load when "Y" connector is used).
"L" Connector
LEDTCL
1a" × 1c" × 4"
"L" connector has male and female connectors,
use to create 90° right angles.
End cap
LEDTCEC
2" × 4" × x"
2" × 2" × 8"
Includes 1 cut end cap and 1 male end cap.
Use to terminate every run to protect
against contaminants.
Mounting Clips
(10 pack)
LEDTCL
2"
For installation on surfaces that are di cult
to adhere to. Two mounting clips per foot
are recommended for straight runs.
Retro t Channel
LEDTRC
36" × 2" × 2"
Use to construct a miniature cove or light ba e
in which tape may be concealed. May also be
mounted to the channel as a way to change
the direction of the projected light.
Rigid Aluminum
Channel
LEDTCH
5' × n” × a”
Mounting channel with acrylic di user.