Installation Sheet

ManualsBrandsWAC Lighting Manualsunder cabinet lightingWAC Lighting InvisiLED Recessed Channels Symmetrical Perpendicular Corner for InvisiLED Tape Light

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2017 1

waclighting.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Factory

44 Harbor Park Drive

Port Washington, NY 11050

Central Factory

1600 Distribution Ct

Lithia Springs, GA 30122

Western Factory

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Symmetrical Recessed Channel

LED-T-RCH1-WT

SAFETY INSTRUCTION

IMPORTANT: NEVER attempt any work without shutting o the

electricity.

• Read all instructions before installing.

• Always turn o power at fuse box prior to installation to

prevent electrical shock.

• Intended for indoor use. Dry and damp locations.

• For installation by a qualied electrician.

• System is intended for installation in accordance with Na-

tional Electric Code, and local regulations.

• Consult with local inspector to assure compliance.

COMPONENTS:

LED-T-RCH1-WT

a) LED-T-CH-PER (8)

b) LED-T-CH-JOIN (1)

LED-TC-B-2L LED-T-CH-PER LED-T-CH-INS LED-T-CH-JOIN LED-T-CH-BIT LED-T-CH-SINK

LED-T-CH-END1-WT

Instruction de sécurité

IMPORTANT: NE JAMAIS tenter tout travail sans couper l'électricité.

• Lisez toutes les instructions avant d'installer.

• Toujours couper l'alimentation électrique à la boîte à fusibles

avant l'installation pour éviter les chocs électriques.

• Destiné à une utilisation en intérieur. endroits secs et humides.

• Pour l'installation par un électricien qualié.

• Le système est destiné à être installé conformément au Code

national de l'électricité, et les réglementations locales.

• Consultez l'inspecteur local pour assurer la conformité.

LED-T-RBOX1-WT (sold separately)

a) LED-T-CH-END1-WT (2) INSTALLED

b) LED-T-CH-JOIN (1)

c) LED-T-CH-SINK (1)

d) LED-TC-B-2L (4)

e) LED-T-CH-BIT (1)

f) LED-T-CH-INS (1)

LED-T-RCH1-COV

Summary of content (14 pages)

PAGE 1
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. • Read all instructions before installing. • Always turn off power at fuse box prior to installation to prevent electrical shock. • Intended for indoor use. Dry and damp locations. • For installation by a qualified electrician. • System is intended for installation in accordance with National Electric Code, and local regulations.
PAGE 2
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT INSTALLATION: 1. Disassemble the Junction Box & Hanger Bars from LED-T-RBOX1-WT (Keep all of the components and screws for later installation.) Junction Box Hanger Bars Channel Connectors Channel Section Screw LED-T-CH-END1-WT End Cap Channel Section LED-T-RCH1-COV Diffuser Channel Cover End Cap Screw waclighting.com Phone (800) 526.2588 Fax (800) 526.
PAGE 3
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 2. Junction Box can be mounted horizontally or vertically by using the Mounting Brackets & Screws depending on the orientation of the channel. Junction Box can be slid along the Hanger Bars by loosening and fastening the Locking Screws on both top and bottom. Remove Knockouts on the Junction Box as necessary before mounting it.
PAGE 4
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 3. Select the location between two Studs for the Junction Box to be mounted. Place the adjustable Hanger Bars between the Studs (14 1/2” to 24 1/2”). Make sure the lips on the Hanger Bars are against the Studs. Use supplied Screws to secure the Hanger Bars at desired position. Min 14 1/2” Max 24 1/2” Studs Hanger Bar Lips Screws waclighting.com Phone (800) 526.2588 Fax (800) 526.
PAGE 5
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 4. Install the conduit and run the low voltage 24V DC Power Wires. Connect the 24V DC power wires to the Wire Adapter LED-TC-B-2L with the provided wire nuts. Tuck all wires into the Junction Box for later use. Junction Box 1/2” Conduit From Remote Power Supply Wire Adapter LED-TC-B-2L waclighting.com Phone (800) 526.2588 Fax (800) 526.
PAGE 6
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 5. Check all wiring connections and make sure all wiring is done as instructed. Plug in the Tape Light Strip and turn on the power to ensure the lights are working properly. Remove the tape light strip for later use if it is powered properly. Tape Light Strip waclighting.com Phone (800) 526.2588 Fax (800) 526.
PAGE 7
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 6. Mark a 2 3/8” x 3” square on the drywall where the junction box will be located. Cut out the marked square using a jabsaw or “Rotozip” tool. Mount the drywall to the studs. Using the drywall opening as reference, mark 2 3/8” wide lines and cut the desired length of the channel along the drywall. Mark the location of the Studs for later use.
PAGE 8
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 7. Insert the End Cap & Channel Section from LED-T-RBOX1-WT to the power feed side & insert one End Cap from LED-T-RBOX1-WT to the opposite side temporarily. Measure the LENGTH OF CHANNEL in between precisely. Write the number down on a paper. Remove the End Caps and Channel Section from the drywall. Channel Section (from LED-T-RBOX1-WT) End Cap (from LED-T-RBOX1-WT) Length of channel (LED-T-RCH1-WT) End Cap (from LED-T-RBOX1-WT) 8.
PAGE 9
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 9. Insert LED-T-CH-JOIN half way into the slots of each channel end and butt the channels against each other. Lock the channels tightly together and secure them with the provide hex key. Mount the LED-T-CH-END1-WT to the end of the channel. Push the whole channel assembly into the drywall cutout. Mount the channel assembly to the Junction Box with End Cap Screw and Channel Section Screw.
PAGE 10
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 10. Make sure channel is aligned straight using a laser level. Use the Marked Stud Locations on the drywall and the Channel Grooves, carefully drill (LED-T-CH-BIT) and countersink (LED-T-CH-SINK) the channel. Properly secure the channel to the drywall using drywall screws. Make sure all screw heads are flush with the channel surface for plaster work later. Stud Markings Channel Grooves Drill and countersink waclighting.
PAGE 11
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 11. Cover up the opening section of the channel with the provided Foam to prevent plaster and dust entering the channel. Apply ultra-thin drywall tape along edges of the channel to prevent cracking of plaster after installation. Note: Do not overlap drywall tapes. Plaster the channel edges to the drywall. Sand and paint the wall properly.
PAGE 12
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 12. Pull out the LED-TC-B-2L from Junction Box. Plug the Tape Light Strip into the Wire Connector. Tuck the wire connector back to the junction box. Removing the backing from the tape light strip and install it inside the channel by using your fingers or the provided tool LED-T-CH-INS. Make sure to push the connector as close to the end of the channel as possible to eliminate dark spot at the beginning of the run.
PAGE 13
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT 13. Screw the Channel Cover back to the channel. Push the Diffuser LED-T-RCH1-COV onto the channel Turn on the power and the installation is finished. Channel Cover Channel Cover Screw LED-T-RCH1-COV Diffuser 14. General Wiring Diagram Remote Remote Remote 277V Black Black Strip Black White White Red Extended Wire Dimmer White waclighting.com Phone (800) 526.2588 Fax (800) 526.
PAGE 14
INSTALLATION INSTRUCTION Symmetrical Recessed Channel LED-T-RCH1-WT LED-T-RCH1-WT Installation Instructions For Angled Configurations Optional Components Offered: LED-T-CTC1-WT LED-T-WTW1-WT LED-T-WTC1-WT Includes: a) LED-T-CH-PER (2) b) LED-T-CH-JOIN (1) Includes: a) LED-T-CH-PER (2) b) LED-T-CH-JOIN (1) Includes: a) LED-T-CH-PER (2) b) LED-T-CH-JOIN (1) Miter cut channel sections to match installation angle. Channel should be cut together with the diffuser to ensure proper fitting.