Installation Guide

ManualsBrandsWAC Lighting ManualsLightingCube Architectural 10" Tall LED Indoor/Outdoor Pendant with 30° Narrow Beam Spread

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.

waclighting.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Cube Architectural - Swivel Canopy Suspension Kit

DC-PDSK

WARNING

- Read all instructions before installing.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch “OFF” the circuit

- Place the wall switch in the “OFF” position.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

FIXTURE INSTALLATION

Figure 1

Note: additional stems (p/n DS-PDX24) can be combined for a maximum length of 96”. Refer to Figures 2-4

Cast ball

5”

1/2”

Junction box

Canopy

Pendant stem

Mounting plate

Canopy

24” stem (X2)

Screws

Fixture plate

Washer

Nut

Feed wire

Feed wire clamp

Components

included with

DS-PDSK

suspension kit

Components

included with

Pendant stem Thread connector Metal cutting tool

Figure.1

Figure.3

Figure.2

Figure.4

96” max

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTION Cube Architectural - Swivel Canopy Suspension Kit DC-PDSK WARNING - Read all instructions before installing. - Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch “OFF” the circuit - Place the wall switch in the “OFF” position. AVERTISSEMENT IMPORTANT : Coupez l’électricité avant TOUTE manipulation. - Lisez toutes les instructions avant d’installer.
PAGE 2
INSTALLATION INSTRUCTION Cube Architectural - Swivel Canopy Suspension Kit DC-PDSK 3. 4. 5. Align the top of the cast ball with the top of the cut pendant stem and temporarily lock it in place by tightening one of the screws into the side of the stem. Use the provided drill bit to drill a hole through the stem wall using the unthreaded hole. Loosen the screw. Rotate the cast ball 180° and retighten the screw. Drill another hole using the unthreaded hole on the other side of the stem wall.
PAGE 3
INSTALLATION INSTRUCTION Cube Architectural - Pendant DC-PD05, DC-PD06 REFLECTOR REPLACEMENT FIG.7) FIG.6 FIG.6) four FIG.7 Remove four clips LED REPLACEMENT FIG.8), remove the panel assembly (FIG.9). 1. 2. Loosen the LED screws and LED holder, carefully disconnect LED quick connector then replace LED. (FIG.10). FIG.8 FIG.9 FIG.10 LED holder Remove panel assembly screws and gaskets Screws LED Connector DRIVER REPLACEMENT 1. Loosen the screw and gasket (See FIG.
PAGE 4
INSTALLATION INSTRUCTION Cube Architectural - Pendant DC-PD05, DC-PD06 OVERVIEW It is surface mount down light, included ceiling mount, pendant mount, single direction wall wash and up-down direction wall wash. Check catalog for various mount type, size, beam angle and color choices. FIXTURE INSTALLATION 1. (See FIG.1) efully not to lose any small parts necessary for installation. 2. Connect all pendant assembly. (See FIG.2) Ther 3.
PAGE 5
INSTALLATION INSTRUCTION Cube Architectural - Pendant DC-PD05, DC-PD06 WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. Go to the main fuse box, or circuit breaker.