User's Manual

OSMAC Base User Manual
Page 13
Manu.01_0405
4UnitSetup
The OSMAC Base supports numerous functions and operating modes. These are programmed via a
series of menus. The following table lists configuration parameters and menus within the OSMAC Base
unit that the user may wish to modify. Operating parameters are stored in non-volatile memory, and will
not need to be reconfigured during the life of the product unless the user wishes to change them. The
default settings are shown in BOLD.
OSMAC BASE COMMAND MENU STRUCTURE
System Configuration
(Key 1 held down during power-up, or CTRL-MENU or ALT-TAB from an external keyboard)
PASSWORD = Contact Distributor
1 SERIAL PORT #1
1 SERIAL DATA BITS
7DATABITS
8DATABITS
2 SERIAL PORT RATE
1-300BAUD
2-600BAUD
3 - 1200 BAUD
4 - 2400 BAUD
5 - 4800 BAUD
6 - 9600 BAUD
7 - 19200 BAUD
3 SERIAL STOP BITS
1STOPBIT
2STOPBITS
4 SERIAL PARITY
EVEN PARITY
ODD PARITY
NO PARITY
5 FLOW CONTROL
NO FLOW CONTROL
HARDWARE CONTROL
6 SERIAL PROTOCOL
1TAP
2COMP1
3COMP2
7TAPTIMEOUT
{30 Seconds default}
8COMPTIMEOUT
{60 Seconds default}
9 MANUAL TIMEOUT
{90 Seconds default}
2 SERIAL PORT #2
1 SERIAL DATA BITS
7DATABITS
8DATABITS
2 SERIAL PORT RATE
1-300BAUD
2-600BAUD
3 - 1200 BAUD
4 - 2400 BAUD
5 - 4800 BAUD
6 - 9600 BAUD
7 - 19200 BAUD
3 SERIAL STOP BITS
1STOPBIT
2STOPBITS
4 SERIAL PARITY
EVEN PARITY
ODD PARITY
NO PARITY
5 FLOW CONTROL
NO FLOW CONTROL
HARDWARE CONTROL
6 SERIAL PROTOCOL
1TAP
2COMP1
3COMP2
7TAPTIMEOUT
{30 Seconds default}
8COMPTIMEOUT
{60 Seconds default}
9 MANUAL TIMEOUT
{90 Seconds default}
3 MODE SELECTION
1 SPEAKER ENABLE
ENABLE
DISABLE
2 BUSY CH LOCKOUT
ENABLE
DISABLE
3 REMOTE PAGING
ENABLE
DISABLE
4 CALL FORWARDING
ENABLE
DISABLE
5 AUTOPATCH TIMER
0 = PATCH DISABLED
DEFAULT = 10 MINUTES
6 VOICE PROMPTS
ENABLE
DISABLE
7WARMUPSIGNAL
ENABLE
DISABLE
8 RINGS TO ANSWER
0= ANSWER IMMEDIATELY
1= DEFAULT
9 NUMBER DONE DELAY
{5 Seconds default}
4 TRANSCEIVER
1 TX SETUP
1TXFREQUENCY
{464.5MHz}
2 TX SIGNALING
1 (CARRIER ONLY)
2CTCSS
3 TX BANDWIDTH
NARROW BAND
WIDE BAND
4 TX DATA DELAY (MS)
{20mSdefault}
5 TX STREAM DELAY
{600mS
default}
2 RX SETUP
1RXFREQUENCY
{464.5MHz}
2 RX SIGNALING
1 (CARRIER ONLY)
2CTCSS
3 SHIFT CPU CLOCK?
DISABLED
ENABLED
3 INVERT CARRIER DETECT
YES
NO
4 INVERT TRANSMIT DATA
YES
NO
5TXTYPE
NO TYPE SELECTED
VHF (MODEL 204)
UHF
VHF (MODEL 3464)
UHF (MODEL 3412-X)
6 TX/RX SWITCH TIME (MS)
DEFAULT = 50 MS
5CWCALLSIGN
{DEFAULT = NONE}
6 DIAGNOSTICS MODE
{See below for details}