User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Installation RF-Orchestra!™ Transmitter Installation and Operation
4-4 6880493G02-C July 2000
Tools and Equipment
The following tables list the tools, test equipment, and locally procured parts needed for
installation, troubleshooting and maintenance. The listed model numbers are recommended,
but equivalent tools and equipment are acceptable. Motorola recommends using various
shades of colored, vinyl tape for wire identification.
Recommended Tools
The following table lists the recommended tools for installation (see Table 4-1). These tools are
not included as part of the RF-O! paging station shipment and must be procured locally.
DANGER
Select tools and equipment that have insulated grips and handles. This
insulation helps prevent potential injury resulting from electrical
shock.
Table 4-1: Recommended Tools for Installation
Tool Model/Type Manufacturer Purpose
Crimping tool 8-pin modular cable Locally procured Customizing T1 connections
Carpenters level or
equivalent
Pro Smartlevel
24 in. w/module
Pro Smartlevel Level Cabinets
Torque wrench Snap-On
/QP1117
(or equivalent
(calibrated to 105 in.
lb)
Snap-On Torque wrench handle for RF connections
1-1/4 in. crow’s foot
adapter
Snap-On/GFC40A Snap-On Torque wrench adapter for Andrew type
7/16 DIN connectors
1-1/16 in. crow’s foot
adapter
Snap-On/GFC34A Snap-On Torque wrench adapter for Huber/Suhner
type 7/16 DIN connectors
TORX
driver set T-15 and T-30 bits Textron Tightening connections
Fiberglass or
wooden stepladder
7 ft. Locally procured Reach connections on top of cabinet