User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Preinstallation RF-Orchestra!™ Transmitter Installation and Operation
3-4 6880493G02-C July 2000
Equipment Cabinet Floor Loading
Table 3-2 shows the typical weight and floor loading information for the X128 cabinet.
Transmitter Breaker Panel Access
Follow all codes required by the National Electrical Code (NEC). The NEC requires a 36-in.
clearance for electrical service access, and requires that all doors to this equipment open to a
minimum of 90 degrees.
Disabled Personnel
The customer is responsible for determining the applicable Americans with Disabilities
Act (ADA) requirements that apply to the site. The ADA requires certain clearances for
handicapped personnel.
Table 3-2: Equipment Cabinet Weight and Floor Loading - Cabinet X128
Configuration Weight
1
1. Weights include optional transmitter and network peripherals. If a co-located RF-A! receiver is supplied, weights
include receiver peripherals
Floor Loading
Model PT1052 Single-channel RF-O! Transmitter
520 lb
236.36 kg
116 lb/ft
2
5.8 kg/m
2
Model PT1054 Two-channel RF-O! transmitter
590 lb
268.18 kg
132 lb/ft
2
6.6 kg/m
2
Model PT1052 One-channel RF-O! transmitter with Option X349
(Single Co-located RF-A! Receiver)
605 lb
275 kg
135 lb/ft
2
6.75kg/m
2
Model PT1054 Two-channel RF-O! transmitter with Option X351
(Two Co-located RF-A! receivers)
715 lb
325 kg
160 lb/ft
2
8 kg/m
2