User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
July 2000 6880493G02-C H-9
RF-Orchestra!™ Transmitter Installation and Operation Debug Traces
July 2000 6880493G02-C H-9
M2HQ 1 1.4.0+ Modulator 2 DSP Modulation Parameters
(See Modulator 1 DSP Modulation
Parameters)
<M2HQ 1>MOD2 FM PARMS: Invert:1, Activate:0, SplatterFilt:000, (Word1: 0x0002)
Ang0:0x00000000, Dev0:0x00199999, Pwr0:0x000000
Ang1:0x00000000, Dev1:0x00199999, Pwr1:0x000000
<M2HQ 1>MOD2 AM PARMS: Invert:1, Activate:0
Angle0:0, Pilot0:0, Upper0:0, Lower0:0
Angle1:0, Pilot1:0, Upper1:0, Lower1:0
<M2HQ 1>MOD2 FM PARMS: Invert:1, Activate:0, SplatterFilt:000, (Word1: 0x0002)
Ang0:0x00000000, Dev0:0x00199999, Pwr0:0x000000
Ang1:0x00000000, Dev1:0x00199999, Pwr1:0x000000
<M2HQ 1>MOD2 AM PARMS: Invert:1, Activate:0
Angle0:0, Pilot0:0, Upper0:0, Lower0:0
Angle1:0, Pilot1:0, Upper1:0, Lower1:0
a<M2HQ 1>MOD2 FM PARMS: Invert:1, Activate:0, SplatterFilt:000, (Word1: 0x0002)
Ang0:0x00000000, Dev0:0x00199999, Pwr0:0x000000
Ang1:0x00000000, Dev1:0x00199999, Pwr1:0x000000
MPCM 1 1.4.0+ Maintenance Path Inbound Message
Trace
Incoming MP message from
communications port with framing stripped
off. The msg is translated into APDU
formats and displayed with content headers.
Cmd
:
D- Get value command
N - Get event or changed value command
W - Write value command
S - Software download command
Z- Repeat last response command
Select
: N-Next, F-First (Only with N or D
command)
Seq
: One byte sequence code repeated
from the Get Event or Changed Value
Command
<MPCM 1> IN MSG-GET EVT: Cmd: N Seq: 112 Select: N
<MPCM 1> IN MSG-GET EVT: Cmd: N Seq: 113 Select: N
<MPCM 1> IN MSG-GET EVT: Cmd: N Seq: 114 Select: N
<MPCM 1> IN MSG-GET EVT: Cmd: N Seq: 115 Select: N
<MPCM 1> IN MSG-GET EVT: Cmd: N Seq: 116 Select: N
Table H-2: Traces
Trace Flag Version Description Example Output