User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
H-8 6880493G02-C July 2000
Debug Traces RF-Orchestra!™ Transmitter Installation and Operation
H-8 6880493G02-C July 2000
M1HQ 1 1.4.0+
Modulator 1 DSP Modulation Parameters
Display information being sent to the
Modulator 1 DSP. FM Parameters:
Invert
: 1 = Invert, 0 = Noninvert
Activate
: 0 - upon next launch
1 - immediately
SplatterFilt
: 000 - 50 kHz chan or 001 - 25 kHz chan
Word1
:First word sent to DSP. Bits define Invert,
Activate, and Splatter Filter.
Ang0
: Modulator 0 FreqInteger
Dev0
: Modulator 0 Deviation
Pwr0
: Modulator 0 Magnitude (default: 0x6d60)
Ang1
: Modulator 1 FreqInteger
Dev1
: Modulator 1 Deviation
Pwr1
: Modulator 1 Magnitude (default: 0x6d60)
AM PARAMS:
Invert
: 0 - Do not invert 1 - Invert spectrum
Activate
: 0 - activation of new params at next launch
1 - immediate activation
Angle0
: Mod 0 subchan freq
Pilot0
: Mod 0 Pilot Magnitude
Upper0
: Mod 0 Upper Sideband Magn.
Lower0
: Mod 0 Lower Sideband Magn.
Angle1
: Mod 1 subchan freq
Pilot1
: Mod 1 Pilot Magnitude
Upper1
: Mod 1 Upper Sideband Magn.
Lower1
: Mod 1 Lower Sideband Magn.
<M1HQ 1>MOD1 FM PARMS: Invert:1, Activate:0, SplatterFilt:000, (Word1: 0x0002)
Ang0:0xffdeaaab, Dev0:0x00199999, Pwr0:0x006d60
Ang1:0x00000000, Dev1:0x00199999, Pwr1:0x000000
<M1HQ 1>MOD1 AM PARMS: Invert:1, Activate:0
Angle0:42aaaa, Pilot0:640, Upper0:308a, Lower0:308a
Angle1:0, Pilot1:0, Upper1:0, Lower1:0
<M1HQ 1>MOD1 FM PARMS: Invert:1, Activate:0, SplatterFilt:000, (Word1: 0x0002)
Ang0:0xffdeaaab, Dev0:0x00199999, Pwr0:0x006d60
Ang1:0x00000000, Dev1:0x00199999, Pwr1:0x000000
<M1HQ 1>MOD1 AM PARMS: Invert:1, Activate:0
Angle0:42aaaa, Pilot0:640, Upper0:308a, Lower0:308a
Angle1:0, Pilot1:0, Upper1:0, Lower1:0
Table H-2: Traces
Trace Flag Version Description Example Output