User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Alarms and Error Messages
July 2000 6880493G02-C F-31
Clearing the Error Logs on OCM (RFO FIPS: a 103)
Enter the RFO FIPS: a 103 command to clear the OCM Alarm Log. Turning off the RF-O!
transmitter, resetting the station using RFO FIPS: a 117 command, or pushing the RESET
button on the RF-O! transmitter will not clear the alarm logs.
RF-O! Error Code/Alarm Code Cross-Reference
The table below shows all of the currently supported RF-O! transmitter Alarms along with the
corresponding Error Log entry.
Table F-4: RF-O! Error Code / Alarm Code Cross Reference
Alarm Text (RFO FIPS: a 99) Corresponding Error Code (RFO FIPS: a 104)
16.8MHz Pendulum Reference Not Phase Locked. E_PENDULUM_NOT_LOCKED
16.8MHz Pendulum Reference Not Detected. E_PENDULUM_REFERENCE_FAILURE
Alarm Occurred Due to OCM Reset. S_STATION_RESET
Catastrophic Exciter Failure Detected. E_EXCITER_FRU_FAIL_ALARM
Circulator Load Temperature Limit Exceeded. E_CIRC_LOAD_TEMP_EXCEEDED
Clipping Detected by the Tranlin During FM
Transmission.
E_STATION_FM_CLIPPING_DETECTED
Clipping Detected by the Tranlin During Voice
Transmission.
E_STATION_AM_CLIPPING_DETECTED
Exciter Synthesizer 1 Has Failed to Lock. E_SYNTH1_LOCK_FAIL
Exciter Synthesizer 2 Has Failed to Lock. E_SYNTH2_LOCK_FAIL
Exciter Tranlin IC 236 MHz Oscillator Failed to
Lock.
E_TXLIN_NOT_LOCKED
Failed to Read A to D Converter using SPI on PA 1
Power Supply.
E_PA1_PS_AD_SPI_READ_FAIL
Failed to Read A to D Converter using SPI on PA 2
Power Supply.
E_PA2_PS_AD_SPI_READ_FAIL
Failed to Read the Exciter A to D Converter. E_EXCITER_AD_READ_FAIL