User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Alarms and Error Messages
July 2000 6880493G02-C F-27
S_OCM_TX_CONTROL_ERROR
A PnP Control Command was invalid.
Reported as an SNMP Trap.
Critical
Verify proper PnP interface connections.
If the error persists, save the error log and
contact Motorola.
S_OCM_TX_DATA_ERROR
A PnP Symbol Data Command was invalid.
Reported as an SNMP Trap.
Major
Verify proper PnP interface connections.
If the error persists, save the error log and
contact Motorola.
S_OCM_TX_PAGING_DISABLED
This error is logged on the RFB, but sourced by the
RFO. An error occurred on the RFO which caused the
RFO to become disabled. When disabled, the TX_OK
line between the RFO and RFB is de-asserted,
notifying the RFB to stop sending PnP data. The
following errors on the RF-O! currently disable the
transmitter:
E_AMPLITUDE_NOT_ALIGNED
E_CIRC_LOAD_TEMP_EXCEEDED
E_DISABLE_PAGING
E_EXCITER_AD_READ_FAIL
E_EXCITER_FRU_FAIL_ALARM
E_EXTERNAL_REFLECTED_POWER_HIGH
E_HIGH_AMBIENT_TEMP_SHUTDOWN_ALARM
E_HIGH_EXT_WM_VSWR_ALARM
E_HIGH_INT_WM_VSWR_ALARM
E_HIGH_STABILITY_REFERENCE_FAILURE
E_INTERNAL_REFLECTED_POWER_HIGH
E_PA_AD_2_TEST_VOLTAGE_FAIL_DECK_1
E_PA_AD_2_TEST_VOLTAGE_FAIL_DECK_2
E_PA_AD_1_TEST_VOLTAGE_FAIL_DECK_1
E_PA_AD_1_TEST_VOLTAGE_FAIL_DECK_2
E_PA_FAIL_SHUTDOWN_ALARM
E_PA_TEMP_SHUTDOWN_ALARM
E_PA1_PS_AD_SPI_READ_FAIL
E_PA2_PS_AD_SPI_READ_FAIL
E_PENDULUM_NOT_LOCKED E_PENDULUM_REFERENCE_FAILURE
E_POWER_LEVELING_FAILED
E_STATION_AM_CLIPPING_DETECTED
E_STATION_FM_CLIPPING_DETECTED
E_SYNTH1_LOCK_FAIL E_SYNTH2_LOCK_FAIL
E_TXLIN_NOT_LOCKED
I_PAGING_ACCESS_DISABLED
Reported as an SNMP Trap.
Critical
Check for related error messages through
RF-O! FIPS. If the error persists, save the
error log and contact Motorola.
Table F-3: RF-O! Transmitter Error/Alarm Code Definitions (Sheet 25 of 27)
Error and Description
Alarm
Severity
Action