User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Alarms and Error Messages
July 2000 6880493G02-C F-21
E_SYMBOL_DATA_COMMAND_FORMAT_ERROR
Sent if one or more of the Symbol Data Command
fields are invalid.
Major
If the error persists, save the error log and
contact Motorola.
NOTE: This is a Plug-and-Play Error.
Transmitter was Disabled for 2 seconds,
and DSP buffers were flushed.
E_SYNTH1_LOCK_FAIL
(formerly E_RFCC_SYNTH1_LOCK_FAIL)
The attempt to reprogram the First Exciter Synthesizer
failed.
Beginning with RF-O! transmitter 1.2.2, the transmitter
is disabled after several attempts to program both
synthesizers has failed.
Critical
Reboot RF-O! transmitter. If the error
persists, save the error log and contact
Motorola.
E_SYNTH2_LOCK_FAIL
(formerly E_RFCC_SYNTH2_LOCK_FAIL)
The attempt to reprogram the Second Exciter
Synthesizer failed.
Beginning with RF-O! transmitter 1.2.2, the transmitter
is disabled after several attempts to program both
synthesizers has failed.
Critical
Reboot RF-O! transmitter. If the error
persists, save the error log and contact
Motorola.
E_SYNTHESIZER_INITIALIZATION_FAILED
The two synthesizers on exciter can not be initialized
and locked. This check is performed when RF-O!
transmitter starts up and initializes the power control.
Critical
Reset RF-O! transmitter. Check
synthesizers. If the error persists, save
the error log and contact Motorola.
E_TIMER_COUNT_PAST_REFERENCE_
COUNT
The periodic timer which controls time-critical tasks
was delayed by a higher priority task, making it
impossible to setup the next timer interrupt. The timer
controls time-critical functions, such as wattmeter
readings. The RFO will self-recover from this error
condition.
NOTE: It is normal for this error to be triggered at the
same time as any of the Plug-and-Play Errors, when
the DSP’s are flushed.
Minor
If a large number of these errors occurs
(more occurrences of this error than all of
the PnP Errors combined), contact
Motorola.
Table F-3: RF-O! Transmitter Error/Alarm Code Definitions (Sheet 19 of 27)
Error and Description
Alarm
Severity
Action