User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Alarms and Error Messages
July 2000 6880493G02-C F-19
E_SPI_TIMEOUT
An SPI access returned a time-out error. This indicates
that the addresses SPI device did not respond within a
defined time-out period.
Major
Verify all backplane connections are
secure and all boards tightly seated. If
error persists, contact Motorola.
E_SRAM_READ_FAULT
Attempt to read from Static RAM failed.
Minor
NOTE: It is normal to see these errors
after reset in a totally operational RF-O!
transmitter. If error occurs after RF-O!
transmitter has completed startup,
contact Motorola.
E_SRAM_WRITE_FAULT
Attempt to write to Static RAM failed.
Major
Reboot RF-O! transmitter. If the error
persists, save the error log and contact
Motorola.
E_START_TIME_ERROR
An invalid Start Time was received in the Plug-and-Play
Control Command.
Major
If the error persists, save the error log and
contact Motorola.
NOTE: This is a Plug-and-Play Error.
Transmitter was Disabled for 2 seconds,
and DSP buffers were flushed.
E_STATION_AM_CLIPPING_DETECTED
(formerly E_EXCITER_AM_CLIPPING_DETECTED)
The Exciter has indicated that it has clipped during an
AM (Voice) transmission.
Beginning with RF-O! transmitter 1.2.2, when Power
Control is Enabled, this error condition will cause the
transmitter to be disabled.
Major
Verify that RF-O! transmitter amplitude is
properly aligned to the correct FM output
power. Verify that Internal and External
Wattmeters are calibrated. These can be
checked by using the RFO FIPS: a 83
(Station Status) command. Verify that all
RF connections on the RF-O! transmitter
are properly connected. If error persists,
contact Motorola.
E_STATION_DEKEYED_KEY_STATE_MISMATCH
This error occurs when the transmitter status is in the
keyed state, but it should be in a dekeyed state.
Major
If the error persists, save the error log and
contact Motorola.
E_STATION_DEKEYED_MOD_MODE_MISMATCH
The modulation type in a key state does not match the
modulation type received.
Major
If the error persists, save the error log and
contact Motorola.
E_STATION_DEKEYED_MOD_STATE_INVALID
The current modulation type is invalid in the dekey
state.
Major
If the error persists, save the error log and
contact Motorola.
Table F-3: RF-O! Transmitter Error/Alarm Code Definitions (Sheet 17 of 27)
Error and Description
Alarm
Severity
Action