User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Alarms and Error Messages RF-Orchestra!™ Transmitter Installation and Operation
F-18 6880493G02-C July 2000
E_POWER_LEVELING_FAILED
Transmitter is disabled due to Power Leveling
attempting to Gain or Attenuate the set power by more
than 1.5 dB. Power Leveling, as indicated by parameter
2999, or using RFO FIPS: a83(Station Status), should
typically be no more than 0.5 or less than -0.5 dB.
OCM needs to be reset to enable transmitter.
Major
Verify Amplitude Alignment is valid (A 83).
Use RFO FIPS: a 192 SPCQ 16 and a
192 SPCQ 64 debug traces to monitor
power leveling and wattmeter readings.
If problem persists, Contact Motorola.
E_PS_INPUT_VOLT_ALARM_DECK_1
Power Supply 1 voltage detected has fallen below
specified limits, flagging a possible power supply
failure.
Major Replace Power Supply 1.
E_PS_INPUT_VOLT_ALARM_DECK_2
Power Supply 2 voltage detected has fallen below
specified limits, flagging a possible power supply
failure.
Major Replace Power Supply 2.
E_QFULL
OS Error: Cannot Send - Message queue full. The
severity of this message depends upon where in the
RF-O! software this error occurred.
Minor/Critical
May cause the RF-O! transmitter to reset.
If error returns, save error log and contact
Motorola.
E_RFCC_INVALID_CHAN_OFFSET
(See “E_INVALID_CHAN_OFFSET” )
An invalid sub-channel offset was received from the
Plug-and-Play Control Command.
Major
If the error persists, save the error log and
contact Motorola.
E_RFCC_INVALID_MOD_TYPE
(formerly E_RFCC_INVALID_MOD_TYPE)
An invalid Modulation Type was received from the Plug-
and-Play Control Command.
Major
If the error persists, save the error log and
contact Motorola.
E_RFCC_SYNTH1_LOCK_FAIL
(See “E_SYNTH1_LOCK_FAIL” )
The attempt to reprogram the First Exciter Synthesizer
failed.
Critical
Reboot RF-O! transmitter. If the error
persists, save the error log and contact
Motorola.
E_RFCC_SYNTH2_LOCK_FAIL
(See “E_SYNTH2_LOCK_FAIL” )
The attempt to reprogram the Second Exciter
Synthesizer failed.
Critical
Reboot RF-O! transmitter. If the error
persists, save the error log and contact
Motorola.
Table F-3: RF-O! Transmitter Error/Alarm Code Definitions (Sheet 16 of 27)
Error and Description
Alarm
Severity
Action