User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Alarms and Error Messages
July 2000 6880493G02-C F-9
E_HIGH_INT_WM_VSWR_ALARM
RF-O! transmitter disabled the transmitter due to a
VSWR reading of greater than 3.0 (Reflected Power is
greater than one-fourth the Forward Power) at the
Internal Detector.
Critical
See
“E_INTERNAL_REFLECTED_POWER_
HIGH”
E_HIGH_STABILITY_REFERENCE_FAILURE
The OCM lost contact with the Ultra High Stability
Reference Oscillator (UHSO).
Critical
Verify RF-B! transmitter controller has
power. Verify reference module is
properly installed in RF-B! transmitter
controller. Verify 10 MHz BNC cable is
properly connected to both RF-O!
transmitter and RF-B! transmitter
controller on backplanes. Check that 10
MHz is signal is present on backplane. If
error persists, contact Motorola.
E_ILLEGAL_IPS_COMMAND
An invalid FIPS command was entered. The command
was ignored
Informational
If command was entered correctly, verify
that command is compatible with software
version. See FIPS document for correct
command formats.
E_ILLEGAL_PARAMETER_WRITE
The user tried to write a Parameter which can only be
written to by RF-O! transmitter software (Application
Write Only). Command was ignored.
Informational
Only attempt to write to writable
parameter ID’s. See FIPS document for
details.
E_ILLTICKS
OS Error: Ticks input out of range.
Minor
If error persists, save error log and
contact Motorola.
E_ILLTIME
OS Error: Time of day input out of range.
Minor
If error persists, save error log and
contact Motorola.
E_INCOMPLETE_FRAME_ERROR
The Distribution DSP has detected that a partial Frame
fragment was received. Possibly due to error in PnP
interface/protocol.
Major
If error persists, save error log and
contact Motorola.
NOTE: This is a Plug-and-Play Error.
Transmitter was Disabled for 2 seconds,
and DSP buffers were flushed.
Table F-3: RF-O! Transmitter Error/Alarm Code Definitions (Sheet 7 of 27)
Error and Description
Alarm
Severity
Action