User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
FIPS Read/Write Commands (ver. 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
E-26 6880493G02-C July 2000
Offset From Center
Frequency - Index 12
r 2112
w 2112 <arg>
Plug-and-Play Control Command Offset From
Center Frequency Index 12.
WARNING: This parameter intended for Lab/
Development use only!
50000
Hz
-50000
Hz
-25000
Hz
Offset From Center
Frequency - Index 13
r 2113
w 2113 <arg>
Plug-and-Play Control Command Offset From
Center Frequency Index 13.
WARNING: This parameter intended for Lab/
Development use only!
50000
Hz
-50000
Hz
-18750
Hz
Offset From Center
Frequency - Index 14
r 2114
w 2114 <arg>
Plug-and-Play Control Command Offset From
Center Frequency Index 14.
WARNING: This parameter intended for Lab/
Development use only!
50000
Hz
-50000
Hz
-12500
Hz
Offset From Center
Frequency - Index 15
r 2115
w 2115 <arg>
Plug-and-Play Control Command Offset From
Center Frequency Index 15.
WARNING: This parameter intended for Lab/
Development use only!
50000
Hz
-50000
Hz
-6250
Hz
Power Leveling
Cutback
r 2999
This parameter keeps track of the current power
leveling amount. When Power Control is enabled,
power leveling is automatically enabled. Typically,
this value should remain between -0.5 and 0.5. If this
value is outside of this range, possibly the Amplitude
Alignment and/or the Internal Wattmeter Calibration
is faulty.
Note: This value is set to 0 upon RF-O! reset.
4.00
dB
-4.00
dB
0
dB
Power Cutback
r 3000
This parameter maintains the current cutback
amount of the station in dB. If the station is shutdown
or disabled, this value is ignored by the RFO
software. Use RFO FIPS: a 83 to see the actual
station status.
Note: This value is set to 0 upon RF-O! reset.
10
dB
0
dB
0
dB
Table E-1: RF-O! Transmitter Parameters—Read/Write Commands (Sheet 26 of 27)
Name and Command
Description
Ranges
Default
Upper Lower