User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
D-25 6880493G02-C July 2000
FIPS Action Commands (ver 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
D-25 6880493G02-C July 2000
Enable Trace
Mode
a 192 NNNN x
Note: NNNN
syntax is case
sensitive
Note: Enabling
traces CAN
affect station
performance...
use traces with
caution. Be sure
to turn off all
unused traces.
Enables a mode which will output the occurrence of certain events to the
FIPS session. The arguments are:
NNNN x (Trace Enabled)
DIAG 1 - Diagnostic Error Log Trace
SPIQ 1 - SPI Activity
SHMI 1 - Power Supply Status
SHMI 2 - Ambient Temperature Status
SHMI 4 - P/A Temperature Status
SHMI 8- Reserved
SHMI 16 - USHO Present Debug
SHMI 32- Pendulum Locked Debug
SHMI 64 - Pendulum Present Debug
SHMI 128 - Exciter Synth 1 Locked Debug
SHMI 256 - Exciter Synth 2 Locked Debug
DIDQ 1 - Start Time Error
DIDQ 2 - Incomplete Frame Error
DIDQ 4 - Modulation Type Error
DIDQ 8 - Frequency Offset Error
DIDQ 16 - Invalid Command Type
DIDQ 32 - Control Command Format Error
DIDQ 64 - Unexpected Symbol Command Error
DIDQ 126 - Symbol Data Command Format Error
DIDQ 256 - End of Command Error
DIDQ 512 - Workahead Window Error
DIDQ 1024 - Check Command Format Error
DIDQ 2048 - Invalid Symbol Duration
MPCM 16 - Remote Software Download Trace
ITCM 1 - K Factor Trace
ITCM 2 - Attenuation Level Trace
ITCM 4 - Cutback Mode Trace
ITCM 8 - PA Deck Trace
ITCM 16 - Power Supply Trace
ITCM 32 - Carrier Null Trace
SPCQ 1 - Protocol Trace
SPCQ 2 - Reserved
SPCQ 4 - Reserved
SPCQ 8 - DSP Flush Frame State Trace
SPCQ 16 - Power Leveling Trace
SPCQ 32 - VSWR Checking Trace
RFCQ 1 - Control Command Trace
RFO FIPS: a 192 SPCQ 16
RFO FIPS: RA 192
RFO FIPS: a 192 SHMI 1
RFO FIPS: RA 192
RFO FIPS:
<SHMI 1> PS: PS1=left: PS2=right
PS1=> 4.22 Volt(s): PS2=> 4.22 Volt(s)
<SPCQ 16> LEVELING: Set=100 W Act=103 W
Lvl Chg=-0.13 dB Total= 1.57 dB
<SHMI 1> PS: PS1=left: PS2=right
PS1=> 4.22 Volt(s): PS2=> 4.24 Volt(s)
<SHMI 1> PS: PS1=left: PS2=right
PS1=> 4.22 Volt(s): PS2=> 4.24 Volt(s)
<SHMI 1> PS: PS1=left: PS2=right
PS1=> 4.22 Volt(s): PS2=> 4.22 Volt(s)
<SHMI 1> PS: PS1=left: PS2=right
PS1=> 4.22 Volt(s): PS2=> 4.24 Volt(s)
<SHMI 1> PS: PS1=left: PS2=right
PS1=> 4.22 Volt(s): PS2=> 4.24 Volt(s)
Name and
Command
Description Example