User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
D-23 6880493G02-C July 2000
FIPS Action Commands (ver 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
D-23 6880493G02-C July 2000
Test Mode Start
a176mp1p2p3
p4 1 b 5 1
Key the station in test mode
m = modulation type
0 = FM
1 = AM
p = pattern (where p1 is for subchannel 1, p2 for
subchannel 2, p3 for subchannel 3, and p4 for
subchannel 4)
0 - No Pattern
1 - FM Big Comma
2 - FM Little comma
3 - FM Staircase 4-level
4 - FM Symbol A (10)
5 - FM Symbol B (11)
6 - FM Symbol C (01)
7 - FM Symbol D (00)
8 - FM Random
9 - FM Reserved
10 - AM 2-tone (400 Hz + 1 kHz)
11 - AM 1-tone (1.7 kHz)
12 - AM Female voice
13 - AM Male voice
b = Number of Blocks per Frame (0..11) 11
Represents a Full Frame.
RFO FIPS: a 176 0 8 0 0 0 1 10 5 1
RFO FIPS: RA 176
<<< RFO TEST MODES >>>
The Station is Keyed in Test Mode ...
RFO FIPS:
RFO FIPS: a 176 ?
RFO FIPS: RA 176
<<< RFO TEST MODES >>>
OCM Test Mode command syntax:
A 176 m p p p p 1 b 5 1
| | | | | | | | |
| | | | | | | | +- fsk level - 3200 sym/sec
| | | | | | | +---- bit speed - 6400 bits/sec
| | | | | | +------- # forward blocks (1 - 11)
| | | | | +---------- frame frequency
| | | | +------------- subchannel 4 pattern (1-13)
| | | +---------------- subchannel 3 pattern (1-13)
| | +------------------- subchannel 2 pattern (1-13)
| +---------------------- subchannel 1 pattern (1-13)
+------------------------- modulation mode (0 = FM, 1 = AM)
Pattern options:
1 - FM Big Comma
2 - FM Little comma
3 - FM Staircase 4-level
4 - FM Symbol A (10)
5 - FM Symbol B (11)
6 - FM Symbol C (01)
7 - FM Symbol D (00)
8 - FM Random
9 - FM Reserved
10 - AM 2-Tone (400 Hz + 1 kHz)
11 - AM 1-Tone (1.7 kHz)
12 - AM Female Voice
13 - AM Male Voice
Test Mode Stop
a 177
Exit Test Mode. Used to dekey the station, after
keying with the RFO FIPS: a 176 command.
RFO FIPS: a 177
RFO FIPS: RA 177
The Station is Dekeyed.
Name and
Command
Description Example