User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
D-22 6880493G02-C July 2000
FIPS Action Commands (ver 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
D-22 6880493G02-C July 2000
Read Tranlin
a 172
This action command returns the current register
settings in the Tranlin IC.
RFO FIPS: a 172
RFO FIPS: RA 172
<<< READ TXLIN IC >>>
Reg 0x00: Invert I/Q = 0x16
Reg 0x01: ASW/PWRC = 0x0e
Reg 0x02: LOA = 0x54
Reg 0x03: LON = 0x31
Reg 0x04: LOR = 0xf1
Reg 0x05: Interval A = 0x14 => 125.00 usec
Reg 0x06: Interval B = 0x27 => 243.75 usec
Reg 0x07: Interval C = 0x00 => 0.00 usec
Reg 0x08: Interval D = 0xca => 1262.50 usec
Reg 0x09: Interval E = 0xcc => 1275.00 usec
Reg 0x0A: Interval F = 0x51 => 506.25 usec
Reg 0x0B: Interval G = 0x7e => 787.50 usec
Reg 0x0C: Interval H = 0xcb => 1268.75 usec
Reg 0x0D: Interval I = 0x40 => 400.00 usec
Reg 0x0E: Interval J = 0x20 => 200.00 usec
Reg 0x0F: Interval K = 0xff => 1593.75 usec
Reg 0x10: Interval L = 0x36 => 337.50 usec
Reg 0x11: Interval M = 0x4d => 481.25 usec
Reg 0x12: IQ Slew = 0x00
Reg 0x13: Pmode/DAC = 0x1f
Reg 0x14: PDAC = 0x7f
Reg 0x15: Ph/Lvl/Loop = 0x13
Reg 0x16: Attenuator = 0x00
Reg 0x17: Manual Sin = 0x00
Reg 0x18: Manual Cos = 0x00
Reg 0x19: Interval N = 0x10 => 100.00 usec
Calculated Checksum = 0x07a8
Actual Checksum = 0x07a8
Information = 0x02
Attenuation = 0xff
Sine = 0xfe
Cosine = 0x96
==========================================
Name and
Command
Description Example