User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
D-15 6880493G02-C July 2000
FIPS Action Commands (ver 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
D-15 6880493G02-C July 2000
Display the Set
Power Level
a 87 x
Read AM or FM Power Amplitude Alignment
based on the current power setting and PA/Power
Supply configuration.
x = Modulation Type
0 = FM
1 = AM
Note: These tables are only used by the RFO
when Power Control is Enabled (RFO FIPS: w
992 1). When power control is disabled the values
stored in parameters 990, 996, 982, 954, 953,
974, 2053, 2054, 2055, and 2056 are used to
control the power output. By default, Power
Control is Enabled upon reset (starting with RFO
1.2.0).
RFO FIPS: a 87 1
RFO FIPS: RA 87
<<< AM AMPLITUDE CONTROL PARAMETERS >>>
Number of Subchannels
Align 1 2 3 4
------------------------------------------------
Power 150 69 69 0 0
K-Factor 990 1.000000 0.678233 0.959166 0.000000
0.000000
Fdback Atten 996 255 229 229 0 0
Phase Trng 982 -10000 -14000 -14000 0 0
Txlin Reg2 954 84 84 20 0 0
Txlin Reg1 953 14 14 14 0 0
Txlin Atten 974 0 0 0 0 0
Mod Dev 2053 4800 4800 4800 0 0
FM Power Lvl 2054 28000 28000 28000 0 0
AM Pilot Pwr 2055 1600 1600 1600 0 0
AM Sdbd Pwr 2056 12426 12426 12426 0 0
-----------------------------------------------
=============================================
RFO FIPS: a 87 0
RFO FIPS: RA 87
<<< FM AMPLITUDE CONTROL PARAMETERS >>>
Number of Subchannels
Align 1 2 3 4
------------------------------------------------
Power 150 50 50 50 0
K-Factor 990 0.408269 0.235714 0.471428 0.707168
0.000000
Fdback Atten 996 255 255 255 255 0
Phase Trng 982 -10000 -14000 -14000 -14000
0
Txlin Reg2 954 84 84 20 20 0
Txlin Reg1 953 14 14 14 14 0
Txlin Atten 974 0 0 0 0 0
Mod Dev 2053 4800 4800 4800 4800 0
FM Power Lvl 2054 28000 28000 14000 9333 0
AM Pilot Pwr 2055 1600 1600 1600 1600 0
AM Sdbd Pwr 2056 12426 12426 12426 12426 0
-----------------------------------------------
=============================================
Name and
Command
Description Example