User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
D-6 6880493G02-C July 2000
FIPS Action Commands (ver 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
D-6 6880493G02-C July 2000
Calibrate
Detector(s)
a 71 x y
Calibrate the Internal/External detector(s)
x = detector
0 = internal
1 = external
y = power value from Wattmeter (in watts)
Note: This command is normally executed
following the RFO FIPS: a75(Initialize Amplitude
Alignment Parameters) command execution.
Power Control must be DISABLED for this
command to function (RFO FIPS: w 992 0).
See Chapter 6, "Maintenance".
Note: This command can take up to 2 minutes to
fully execute. The printing of the Output Report,
shown in the example, will indicate completion of
the command. Do not type any other FIPS
commands while calibration is occurring.
RFO FIPS: a 71 0 210
Please wait. Command in process...
RA 71
<<< CALIBRATE DETECTORS >>>
========= Detector 0 Calibration =========
0x00: 0x44 0x45 0x54 0x30 "DET0"
0x01: 0x30 0x32 0x31 0x30 "0210"
0x02: 0x32 0x2e 0x36 0x36 "2.66"
0x03: 0x32 0x30 0x35 0x34 "2054"
0x04: 0x44 0x45 0x54 0x30 "DET0"
0x05: 0x44 0x45 0x54 0x30 "DET0"
0x06: 0x44 0x45 0x54 0x30 "DET0"
0x07: 0x44 0x45 0x54 0x30 "DET0"
0x08: 0x44 0x45 0x54 0x30 "DET0"
0x09: 0x44 0x45 0x54 0x30 "DET0"
0x0a: 0x44 0x45 0x54 0x30 "DET0"
0x0b: 0x44 0x45 0x54 0x30 "DET0"
0x0c: 0x31 0x2e 0x30 0x2e "1.0."
0x0d: 0x31 0x20 0x00 0x00 "1 .."
0x0e: 0x30 0x30 0x30 0x31 "0001"
0x0f: 0x43 0x48 0x4b 0x9e "CHK."
0x3f: 0x43 0x48 0x4b 0x26 "CHK&"
Calibration Factor = 1.011365
==========================================
Name and
Command
Description Example