User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
D-3 6880493G02-C July 2000
FIPS Action Commands (ver 2.0.0) RF-Orchestra!™ Transmitter Installation and Operation
D-3 6880493G02-C July 2000
PA EEPROM
Read
a 66 x y
Reads the 4 byte segment specified by argument
‘y’ Serial EEPROM from the P/A specified in
argument ‘x’
x = P/A Number (range 1..2)
y = EEPROM Region to be read in hex.
RFO FIPS: a 66 1 0x00
RFO FIPS: RA 66
<<< READ PA EEPROM >>>
PA 1 EEPRM Cell 0x00 = 0x05 0x06 0x07 0x08
PA EEPOT Write
a67xyssawpw
Writes to the EEPOTs of the P/A’s.
x = PA number (range 1..4)
y = phase/attenuation cell (range 0..3)
ss = Stack Select (range 0..1)
aw = Attenuation Wiper (range 0..FF hex)
pw = Phase Wiper (range 0..FF hex)
Note: To reset the PA to the EEPROM settings
tenter RFO FIP: a 67 x 0 where x is the PA
number.
WARNING: This command intended for Lab/
Development use only!
RFO FIPS: a 67 ?
RFO FIPS: RA 67
<<< PA EEPOT WRITE >>>
Usage: A 67 x y ss aw pw
x = PA Number (Maximum 4 for Current Configuration)
y = Phase/Attenuation Cell (0..3)
ss = Stack Select (0..1)
aw = Attenuation Wiper (0..ff hex)
pw = Phase Wiper (0..ff hex)
RFO FIPS: a 67 1 0 0 AF 2F
Name and
Command
Description Example