User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Backplane Connectors RF-Orchestra!™ Transmitter Installation and Operation
B-2 6880493G02-C July 2000
Connector Pinouts
The following tables provide the OCM connector pinouts (see Table B-2 through Table B-6).
Table B-1: RF-O! Transmitter Backplane Connectors
Connectors Name Description
Connectors numbered J1, 2, and 3 are internal module connections
J4 PLUG-N-PLAY Transmitter controller interface protocol standard
J5, J6 PA#1 and #2 Power amplifiers control and diagnostic SPI interface
J7, J8 PS Current Monitor
(PA#3 and PA#$)
Only used in model PT1052 (single PA) for measuring power supply
current
J9 INT WMTR Internal RF wattmeter SPI interface
J10 EXT WMTR External RF wattmeter SPI interface
J11 EXT REF 10 MHz input must meet the minimum paging station interface
protocol requirements for amplitude and frequency stability
J12 EXT_LOAD_TEMP External circulator load temperature input monitor signal
J13 SYNC PORT Factory use only
J14 LOCAL COMM Factory use only
J15 PLUG-N-PLAY
POWER
+28 V source for RF-Baton! (RF-B!) transmitter controller power as
defined by paging station interface protocol
J16 WILDCARD I/O Interfaces to external input/output circuits or module interfaces
J17 DC FAN POWER RF-O! transmitter chassis fan connection +12 V operation
J18 AUX 5 V +5 V source limited to 50 mA maximum current
J19 AUX A+ +12 V source limited to 50 mA maximum current
J20-J21 DC INPUT + 28 V input from each AC power supply
J22 DC FAN POWER RF-O! transmitter chassis fan connection +12 V operation
J23 RF OUT RF output from exciter circuits for direct connection to a single PA
deck or the RF splitter with multiple PA decks
J24 RF FEEDBACK RF input from internal RF coupler at the RF output