User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Contents
July 2000 6880493G02-C xxvii
Cabinet Installation, 4-6
Cabinet, 4-6
Cabinet Ground Connections, 4-8
Antenna Connections, 4-11
Paging Station Antenna, 4-11
GPS Antenna, 4-12
Co-located RF-A! Receiver(s) Connections, 4-12
Network Connection, 4-12
AC Power Connection, 4-17
Powering Up the RF-O! Paging Station, 4-19
Operation, 5-1
Establishing an RF-O! FIPS Session, 5-1
Service Terminal Setup, 5-1
FIPS Commands, 5-3
Reset and Initialization, 5-6
Operation Modes, 5-7
Normal Paging Mode, 5-7
Trace Mode, 5-7
Test Data Mode, 5-8
Alarm and Error Logs, 5-11
Alarm Log, 5-11
Error Log, 5-12
Software Log, 5-13
General Operational Setup and First Time Use, 5-14
Recording Data for the RF-O! Paging Station, 5-14
RF-O! Paging Station Operational Checkout, 5-15
RF-O! Paging Station Parameters, 5-23
RF-O! Power Control, 5-24
Power Metering, 5-26
Wattmeter Calibration, 5-26
Amplitude Alignment, 5-27
Power Set, 5-28
Module Monitoring, 5-29
Power Cutback/Shutdown, 5-29
Power Leveling, 5-30
Alarm Reporting, 5-31
Subchannel Configuration Control, 5-31
Power Amplifier Configuration Control, 5-31