User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Maintenance RF-Orchestra!™ Transmitter Installation and Operation
6-98 6880493G02-C July 2000
28. Once the startup banner appears on the RFO FIPS session after the cutover has occurred,
check the active bank and software version number with the following commands.
Note: In this example, the active bank is now Bank B, and the active software version is 1.2.5.
29. After the cutover has occurred, the parameters changed by a DIP 2 will be reset to their
default values. The previous operational values can be found in Table 6-8 and Table 6-9:
Additional Parameter List. On the RFO FIPS session, read the minimum set of parameter
values to determine the current value of each parameter. The values read will be shown
on the RFO FIPS session instead of the xxx shown in the responses below.
>>>>>>> CRITICAL PARAMETERS PRESERVED ON CUTOVER <<<<<<<
>>>>>>> --FACTORY PRESETS PRESERVED-- <<<<<<<
>>>>>>> ALL OTHER PARAMETERS SET TO DEFAULTS <<<<<<<
RFO FIPS: r 901
RFO FIPS: RR 901 2
RFO FIPS: r 148
RFO FIPS: RR 148 1.2.5
RFO FIPS: r 141
RFO FIPS: RR 141 xxx
RFO FIPS: r 142
RFO FIPS: RR 142 xxx
RFO FIPS: r 143
RFO FIPS: RR 143 xxx
RFO FIPS: r 144
RFO FIPS: RR 144 xxx
RFO FIPS: r 145
RFO FIPS: RR 145 xxx
RFO FIPS: r 146
RFO FIPS: RR 146 xxx
RFO FIPS: r 997
RFO FIPS: RR 997 xxx
RFO FIPS: r 1023
RFO FIPS: RR 1023 xxx