User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Maintenance
July 2000 6880493G02-C 6-97
24. After about 5 to 15 minutes the following trace should appear on the RFO FIPS session:
25. The number of packets written should keep increasing during a successful download.
For example, the rfo113 image will continue increasing up to 8200 records downloaded
before an automatic cutover occurs. The number of records to download is release
dependent, and should be provided in future release notes. The software download will
take approximately 25 to 30 minutes.
26. On the RFO FIPS session, if the Software Records Downloaded does not appear to be
increasing, verify that no SWDNLD or TFTP errors are logged in the a 110 or a 104 error
logs on the RF-B! transmitter controller. This is verified by typing a 110 and a 104 on the
RFB FIPS session and reviewing any error messages returned. If there are any
Maintenance Path error messages in the log and the download packet message does not
appear to be incrementing on the RFO FIPS session, then the download process has been
disrupted.
27. Once the download completes, the RF-O! transmitter will execute an automatic cutover.
If the RFO FIPS session cutover was successful, the startup banner should appear as
follows:
RFB FIPS: r 432
RFB FIPS: RR 432 200
<MPCM 16> SFWR DNLD: Status: 100 Software Records Downloaded
<MPCM 16> SFWR DNLD: Status: 200 Software Records Downloaded
<MPCM 16> SFWR DNLD: Status: 300 Software Records Downloaded
RFB FIPS: a 104
RFB FIPS: a 110
CAUTION
DO NOT RESET THE RF-O! transmitter. Resetting the RF-O! transmitter in this
state could cause the paging station to disable. This would require a site visit to
replace the RF-O! Flash Memory SIMM.
>>>>>>> MOTOROLA RF-ORCHESTRA! <<<<<<<
>>>>>>> WIRELESS MESSAGING SYSTEM (WMS) <<<<<<<
>>>>>>> (c) Copyright 1998 Motorola, Inc. <<<<<<<
>>>>>>> All Rights Reserved. <<<<<<<