User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Maintenance RF-Orchestra!™ Transmitter Installation and Operation
6-96 6880493G02-C July 2000
21. Turn on the Maintenance Path Software Download trace in the RFO FIPS session by
entering the following command:
22. Start the RF-O! transmitter download in the RFB FIPS session by entering the following
command:
23. The RF-B! transmitter controller receives the image in about 5 to 20 minutes depending
on network traffic. The RF-B! transmitter controller transfers the image to the RF-O!
transmitter through the Maintenance Path.
Verify the RF-B! transmitter controller is receiving packets from the TFTP server by
entering a command on the RFB FIPS session of r 432 several times.
The value given by xxx should start with a value of 100 and increase in increments of 100
once the download from the TFTP server to the RF-B! transmitter controller begins. The
xxx returned by the r 432 command is the number of TFTP packets transferred to the
RF-B! transmitter controller. It may take a few seconds after the a311command is entered
before the value in the r 432 command is reset to 0 and the download from the TFTP
server begins.
The number of TFTP packets to download is release dependent. This information should
be provided in future release notes. For example, the number of TFTP packets for the
rfo113 image is around 2000+ packets for a complete RF-O! transmitter software image.
RFO FIPS: a 192 MPCM 16
RFO FIPS: RA 192
RFB FIPS: a 311
RFB FIPS: r 432
RFB FIPS: RR 432 2100
RFB FIPS: r 432
RFB FIPS: RR 432 2100
RFB FIPS: r 432
RFB FIPS: RR 432 2100
RFB FIPS: r 432
RFB FIPS: RR 432 2100
RFB FIPS: r 432
RFB FIPS: RR 432 2100
RFB FIPS: r 432
RFB FIPS: RR 432 100