User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
RF-Orchestra!™ Transmitter Installation and Operation Maintenance
July 2000 6880493G02-C 6-61
11. Align the internal power meter to the reference power meter by sending the RFO FIPS
command: a 71 0 xxx; where “xxx” is the reading of the reference power meter and “0”
indicates the internal power meter. Calibration may take up to two minutes to complete.
---------------------------------------------
The Accuracy of This Meter is +- 10 %.
=============================================
RFO FIPS: a 71 0 200
Please wait. Command in process...
RA 71
<<< CALIBRATE DETECTORS >>>
========= Detector 0 Calibration =========
0x00: 0x44 0x45 0x54 0x30 "DET0"
0x01: 0x30 0x32 0x30 0x30 "0200"
0x02: 0x32 0x2e 0x31 0x35 "2.15"
0x03: 0x37 0x39 0x38 0x35 "7985"
0x04: 0x44 0x45 0x54 0x30 "DET0"
0x05: 0x44 0x45 0x54 0x30 "DET0"
0x06: 0x44 0x45 0x54 0x30 "DET0"
0x07: 0x44 0x45 0x54 0x30 "DET0"
0x08: 0x44 0x45 0x54 0x30 "DET0"
0x09: 0x44 0x45 0x54 0x30 "DET0"
0x0a: 0x44 0x45 0x54 0x30 "DET0"
0x0b: 0x44 0x45 0x54 0x30 "DET0"
0x0c: 0x31 0x2e 0x32 0x2e "1.2."
0x0d: 0x33 0x20 0x00 0x00 "3 .."
0x0e: 0x30 0x30 0x30 0x30 "0000"
0x0f: 0x43 0x48 0x4b 0xac "CHK."
0x3f: 0x43 0x48 0x4b 0xea "CHK."
Calibration Factor = 1.188193
=============================================