User Manual
Table Of Contents
- Human Exposure Compliance 1
- Introduction 1
- System Description 2
- Wireless Messaging System Overview
- FLEX, ReFLEX, and InFLEXion Messaging Protocol Overview
- RFO! Transmitter Functional Description
- RFO! Paging Station Options
- Hardware Options
- Software Options
- Network Peripheral Options (Option X267)
- RF-Baton! Transmitter Controller without GPS Receiver (Option X594)
- RFB! Transmitter Controller with GPS Receiver (Option X179)
- Battery Revert (Option X649)
- RFO! Transmitter Peripheral Options (Option X263)
- RFA! Receiver (Option X349, X351, X352, X353)
- RFA! Receiver Peripheral Package (Option X88, X89)
- Equipment Specifications
- Electrical Requirements
- Preinstallation 3
- Installation 4
- Operation 5
- Establishing an RF-O! FIPS Session
- Reset and Initialization
- Operation Modes
- Alarm and Error Logs
- General Operational Setup and First Time Use
- RF-O! Paging Station Parameters
- RF-O! Power Control
- Power Metering
- Wattmeter Calibration
- Amplitude Alignment
- Power Set
- Module Monitoring
- Power Cutback/Shutdown
- Power Leveling
- Alarm Reporting
- Subchannel Configuration Control
- Power Amplifier Configuration Control
- Carrier Feedthrough Nulling
- RF-O! Ambient Temperature Monitoring
- High Ambient Temperature Cutback/Shutdown Operation
- High PA vs. Ambient Temperature Cutback/Shutdown Operation
- Maintenance 6
- Troubleshooting
- Check Front Panel Indications
- Verify Data from the RFB! Transmitter Controller
- RFO! Transmitter Status
- Power Cutback LED is Blinking
- Power Cutback LED is Continuously Illuminated
- Check for Plug-and-Play Errors
- Check Control Data Received by the RFO! Transmitter
- Check RF Power Path
- Check Transmitter Frequency
- Check RF-A! Receiver Functionality
- Pages Not Received
- Voice Quality Diagnostics
- Removal and Replacement
- Cabinet Doors Removal
- Cabinet Doors Replacement
- DC-DC Converter Removal
- DC-DC Converter Installation
- Orchestra Control Board Removal
- Orchestra Control Board Installation
- Exciter Removal
- Exciter Installation
- Power Amplifier Removal
- Power Amplifier Installation
- Power Supply Removal
- Power Supply Installation
- Wattmeter (Power Detector) Removal
- Wattmeter (Power Detector) Installation
- Battery Removal
- Battery Installation
- AC Distribution Panel Removal
- AC Distribution Panel Installation
- RFO! Transmitter Backplane Removal
- RFO! Transmitter Backplane Installation
- RF-A! Receiver Removal and Replacement
- RFB! Transmitter Controller Removal and Replacement
- Resetting the Parameter Database
- Paging Station Alignment
- Temperature Calibration Procedure
- Software Download
- Troubleshooting
- Abbreviations and Acronyms A
- Backplane Connectors B
- Model and Options Charts C
- FIPS Action Commands (ver 2.0.0) D
- FIPS Read/Write Commands (ver.2.0.0) E
- Alarms and Error Messages F
- Transmitter Alignment Checklist G
- Debug Traces H
Maintenance RF-Orchestra!™ Transmitter Installation and Operation
6-58 6880493G02-C July 2000
Internal Wattmeter Calibration
This procedure will align the RF-O! transmitter internal power meter to a reference power
meter. The Reference meter must be at least 3% accurate and traceable to the National Bureau
of Standards. Any error in the Reference will be passed to the RF-O! transmitter power meter.
1. Ensure the Tx output is connected to the 500 watt 50 ohm load, and the network is
disconnected at the BCM.
2. For a single PA system, disconnect the PA output cable (at the PA) and connect the
characterized coupler to the output of the PA. Connect the RF cable to the coupler output
port. For multiple PA systems, connect the characterized coupler to the output of the
combiner.
3. Connect the reference power meter to FORWARD tap on the characterized coupler. Set
the offset of the power meter with attenuation written on the characterized coupler.
4. Initialize the internal cal factor on the OCM with the RFO FIPS command: a 72 2 0 0 0 0
5. Reset the OCM with the RFO FIPS command: a 117
RFO FIPS: a 72 2 0 0 0 0
RFO FIPS: RA 72
<<< WRITE EXCITER EEPROM >>>
Exciter EEPROM Cell 0x02 = 0x00 0x00 0x00 0x00
RFO FIPS:
RFO FIPS: a 117
>>>>>>> MOTOROLA RF-ORCHESTRA! <<<<<<<
>>>>>>> WIRELESS MESSAGING SYSTEM (WMS) <<<<<<<
>>>>>>> (c) Copyright 1998 Motorola, Inc. <<<<<<<
>>>>>>> All Rights Reserved. <<<<<<<
>>>>>>> PARAMETER DATABASE UNCHANGED <<<<<<<
ENTER PROTOCOL
fips
ENTER PASSWORD