RCD 510 Specification&Installation (RCD 510 2009 ~ ) -. MODEL: QVL – RCD510-V0 -.
INDEX - Feature…………………………………………………………………....3 Precaution………………………………………………………………..4 Main Spec………………..…………………………………………….…5 System Composition..………………………………………………....6 Outline Dimension……………………………………………………...7 External Appearance……………………….…………………………..8 Connector Pin Assignment…………………………………………..10 DIP Switch Setting……………………………………………………..12 How to use remote……………….…………………………………....13 OSD(On Screen Display)…………………………………………......14 How to use parking guide line ………………………………...…....
-RCD 510 Feature - High Quality - Auto detection for NTSC, PAL signals - AV source switching by remote and toggle switch - Possible to control displayed external NAVI, AV image - AV source controlling by original touch -3-
-Precaution - You must keep the car key taken off from the car while you work this and finally, connect power of the interface. - When to connect the interface cable, you must keep the power cable taken off. - You must work this at the environment without any static electricity or damages. - All of process on this installation should be done by professionals. - You must not break the labels attached on the board, if it’s broken, no warranty.
-Main Spec. 1. Input Spec. (MULTI VIDEO INTERFACE) -. 3 x A/V Input (External video source). -. 1 x CVBS(REAR CAMERA) Input. (Rear camera source) -. 1 x Analog RGB Input (Navigation System output) -. 1 x LCD Input (Car system Input) -. 1 x OEM Input 2. Output Spec. -. 1 x OEM Output -. 4 x Audio Select (12V power comes out from 4wires of cable by video, Navi mode) 3. Power Spec. - Input Power : 8VDC ~ 24VDC - Consumption Power : 12WATT, Max 4.
-System Composition IR NAVIGATION Input (Analog RGB) Switch for source toggle MCU DISPLAY A/V 1 A/V 2 A/V 3 VIDEO MUX Car Installation OEM LCD VIDEO CIRCUIT CVBS (Rear camera) Car Screen Input (CAR MAIN BOARD) POWER CIRCUIT A/V OUT Power Input (+8VDC ~ +24VDC) Dip S/W -6- HEADREST MONITOR
-Outline Dimension 125mm * 105mm * 22mm 125mm 105mm 22mm -7-
-External Appearance LED DIP S/W Remote LCD-OUT From Interface NAVI Touch From OEM BD (Touch OUT) To Touch Screen (Touch IN) FPC POWER AV(IN/OUT) RGB(IN) MODE -8-
-External Appearance POWER AV(IN/OUT) LCD-OUT Remote -9- RGB(IN) DIP S/W MODE LED
-Connector Pin Assignment *RGB-IN Connect *Power Connect ① ② ③ ④ ⑤ ① ACC (Red) ② GND (Black) ③ CAN-H (N.C) ④ CAN-L (N.C) ⑤ MMI (N.C) ⑥ SAFE (Violet) ⑦ REAR-C (Grey) ⑥ ⑦ ① ② ③ ④ ⑤ ⑥ ⑦ ① R DATA (Red) ② G DATA (Green) ③ B DATA (Blue) ④ SYNC (White) ⑤ GND (Black) ⑥ N.C ⑦ N.
-Connector Pin Assignment * Power Cable FILTER & FUSE BOX ACC : 12v~24V GND CAN H (N.C) CAN L (N.C) MMI (N.
-DIP SW Setting ※ ON : DOWN, OFF : UP ; Default : all OFF #PI N FUNCTION 1 RGB INPUT MUTE 2 A/V 1 MUTE DIP S/W Selection ※DIP S/W Use Example ON : Skipping RGB Mode OFF : RGB Display ON : Skipping A/V 1 OFF : A/V1 Display 3 A/V 2 MUTE ON : Skipping A/V 2 OFF : A/V2 Display 4 A/V 3 MUTE ON : Skipping A/V 3 OFF : A/V3 Display -. Use Input Mode : A/V2, A/V3 -. Use original Navigation ▷ ▷ ▷ ▷ ▷ 5 N.C 6 N.C 7 When to choose rear mode (ON : CVBS4, OFF : MAIN) 8 N.
-How to use remote POWER , PIP : N.
-OSD(On Screen Display) · Analog RGB Mode · Video Mode IMAGE Menu - BRIGHTNESS:It is used to adjust brightness of the screen. - CONTRAST: It is used to adjust distinction (Image noise clearness). - SATURATION: Adjust the saturation the picture. - HUE: It is used to adjust the display hue adjustment of the screen. - SHARPNESS: Adjust the sharpen or soften the picture.
OSD(On Screen Display) · Analog RGB Mode · Video Mode OSD Menu - LANGUAGE - TRANSPARENT - H_POSITION : Move the position of AV sources to Left, Right - V_POSITION : Move the position of AV sources to Up, Down -15-
OSD(On Screen Display) · Analog RGB Mode · Video Mode UTIL Menu - FACTORY RESET : Initializing of all values of OSD setting (Impossible to reset of screen position, only possible for functions in OSD) -16-
-Factory Mode · Factory Mode - Operated by pressing ▲ → ▼ → ▲ →MENU of remote or keypad in order.
-Factory Mode : Parking Guide Line Factory Default : PARK ENABLE – OFF ① ① Set “PARK ENABLE” to “ON” on The park mode like the left picture no.1 * If you would like to remove this line, just select “ON” on the above process. ② ② After setting, once you put the gear to rear, the screen displays the parking guide line like the left picture no. 2.
Factory Mode : Parking Guide Line ③ ③ The way to move the lines : Once you operate “*Factory Mode” again, when the lines are appeared, OSD image will be displayed like the left picture no.3 After that, you select “PARK” and can move the lines by ‘UP’,’DOWN’ keys of keypad.
Product Composition - LCD cable 1 EA - Toggle Switch 1 EA - A/V cable 1 EA - Sub Board 1 EA - 지지대 2 EA -Remote - Navi Cable 1 EA - Power Cable 1 EA - IR cable 1 EA - FPC Cable 1 EA - Touch Cable 3 EA ( 8P , 4P , FFC ) -20-
Installation Structure To MAIN LE D NAVI TOUCH DIP S/W IR LCD OUT TOUCH(OUT) TOUCH(IN) FPC RCD VIDEO INTERFACE POWER A/V(IN/OUT) RGB(IN) MODE Head Unit Original FFC REAR-C SAF E F-CAM-DET CAN(L) Original Touch CAN(H) AV/OUT AV3 AV2 AV1 REAR C GND ACC : 12v~24V R G B S Y N C G N D AUDIO R Y e l R E D W h i VIDEO Y e l AUDIO L -21- Original Connector Monitor
-Installation Guide 1. Original FPC cable connection ○ After separating LCD and Head unit board, take apart the original FPC cable. To insert the original cable ○ Connect the separated FPC cable to provided Interface FPC cable (TO LCD), connect the Interface FPC cable (To CTRL BD) to the original connector.
-Installation Guide 2. Touch Cable connection ○ After taking apart the original touch cable from LCD side, connect the provided interface touch cable. (Refer to the below how to connect) Provided interface Touch IN cable Provided interface Touch OUT Original touch cable Original Connector ○ Insert the provided “Touch Out” Cable to the original connector like the above picture. ○ Connect the original touch cable (FPC) to the provided “Touch IN” cable.
-Installation Guide 3. Daughter Connection Interface ○ Connect daughter board with the other cables like the above picture ○ Fix the both edge points on the backside of LCD by supporter panel.
-Precaution in Installation ※ Recommended installation method Like the left pictures, for safety, connect the original cable which was connected with Touch IN cable, after taking out to head unit side. Otherwise, LCD might be able to be damaged by contact error of LCD connector. Connect Touch cable taken out to head unit side to out side like the left picture.
-FAQ 1. When can not change mode. -. Check if the IR Cable (Remote) is connected or not. -. Check if LED is turned on or not. If it is not turned on, Check if power cable is connected or not. 2. When the screen is displaying only black color. -. Check if 2nd LED is turned on or not. If it is not turned on, please check all video sources that you will connect with the interface is operating well or not. -. Check if interface is connected well -.
