USER MANUAL TORNADO 547 LUMEN LAW ENFORCEMENT LED FLASHLIGHT FL-E25P
Thank you for choosing Vulta. The Vulta Tornado FL-E25P projects a crisp, white light with a smooth beam. Perfect for law-enforcement applications, the FL-E25P uses an intuitive dual-control system that’s easy to operate in emergency scenarios. Just rotate the continuously-variable control ring to adjust the output from a minimum 0.5 lumens to a blinding maximum 541 lm, and continue rotating to access the strobe mode. The tailcap button activates temporary-on and constant-on modes.
with high drive-current. The LED is housed in an ultraclear, tempered glass lens that optimizes resistance to impacts and scratches and maximizes throw distance. Crafted from MIL-SPEC Type III hard anodized aluminum alloy with a stainlesssteel bezel, and with a waterproof rating of IPX-8, the FL-E25P is a rugged tool that will withstand harsh environments. There is also a tactical ring for advanced grip and law-enforcement flashlight techniques.
PRECAUTIONS ⚠⚡ • Please read and follow these instructions and keep this manual in a safe place. • This flashlight is extremely bright and can cause temporary or even permanent blindness. Do not shine the flashlight in the eyes of any person or animal. When powering on the flashlight, make sure to point it down or away from you and anyone else. • The surface of this product can become hot after prolonged use. Be careful when touching it and make sure to keep it away from anything flammable or combustible.
or brands, or old and new batteries. • Install the batteries in the proper orientation as indicated by the instructions in this manual. • This product is waterproofed for freshwater only. If it comes into contact with salt water, immediately dry the flashlight and remove the batteries, reassemble, and rinse with freshwater. Dry thoroughly and install new batteries. • Do not attempt to disassemble or repair this product. It is dangerous and will also void the warranty. • Keep this product away from children.
PRODUCT DIAGRAM A LED B LAMP HEAD A C HEAT SINK AREA B D VARIABLECONTROL RING C E TACTICAL RING F LANYARD EYELET G O-RING H TAILCAP I TAILCAP BUTTON J LANYARD SLOTS Also Included: D E F G HOLSTER LANYARD SPARE O-RING H USER MANUAL TWO-YEAR LIMITED WARRANTY 06 VULTA TORNADO I J
A Note about Maximum Output When the flashlight is in High mode, the battery discharge, drive circuit, and LED will all be producing heat, and the lamp head may become extremely hot. Please be cautious when touching it. To protect the battery, circuit, and LED, and to extend the lifetime of the flashlight, we do not recommend continuously running the flashlight on High mode for more than 10 minutes. INSTALLING BATTERIES The Tornado FL-E25P can be powered by two CR123 or RCR123 (3 or 3.
OPERATION The FL-E25P employs a tailcap button for temporary- and constant-on, and a variablecontrol ring to control output power and engage strobe mode. POWERING ON THE FL-E25P Constant On: To turn on the FL-E25P, press the tailcap button all the way until it clicks. Use the variable-control ring to set the flashlight to the desired output (see Adjusting the Output). Temporary On: Temporary-on mode is ideal for a quick burst of light.
ring operates in both temporary-on and constant-on modes. Standby Mode: In constant-on mode, you can rotate the variable-control ring to the OFF position to enter standby mode. This lets you work directly with the variable-control ring to turn the light on and off and to adjust brightness. Strobe Mode: Strobe mode continuously emits quick flashes of bright light. To enter strobe mode, rotate the variable-control ring clockwise until the arrow is aligned with the ].
O-RING MAINTENANCE The Tornado FL-E25P’s O-ring is installed on the threaded portion to help seal out water. The O-ring is prelubricated to extend its lifetime, ensure smooth operation, and increase water resistance. If the O-ring dries out or there is little or no lubricant remaining, we recommend applying a small amount of O-ring lubricant. The FL-E25P comes with a replacement O-ring. If the original wears out after longterm use, replace it with the included spare.
SPECIFICATIONS OUTPUT Maximum, Strobe: 547 lm Minimum: 0.5 lm BEAM INTENSITY 22,500 cd LED TYPE CREE XM-L2 POWER SOURCE Two CR123 or RCR123 (3 or 3.7 V) batteries or one 18650 (3.7 V, 2600 mAh capacity with overcharge protection) battery RUNTIME Maximum: 2 hr. Minimum: 120 hr. CONSTRUCTION Body: MIL-SPEC Type III hard anodized aerospace-grade aluminum alloy Bezel: Stainless steel Lens: Tempered glass IMPACT RESISTANCE Up to 6.5´ (2 m) WATERPROOFING IPX-8 standard, up to 6.
TWO-YEAR LIMITED WARRANTY This VULTA product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of two (2) years from the original purchase date or thirty (30) days after replacement, whichever occurs later.
