INSTALLATION & OPERATION MANUAL VW & VSL SERIES DRAWER WARMERS VCW1, VCW2 CHIP WARMERS MODELS: CHIP WARMERS: VCW1 VCW2 ML-138038 ML-138041 DRAWER WARMERS: CAFÉ’: VW1S VW2S VW3S VW4S ML-126500 ML-126502 ML-126504 ML-126506 CAFE’ BUILT-IN: VW1SB VW2SB VW3SB VW4SB ML-126501 ML-126503 ML-126505 ML-126507 SLIMLINE LOW PROFILE: SLIMLINE BUILT-IN: VW1C VW2C VSL1 VSL2 ML-126516 ML-126518 VW1CB VW2CB ML-126508 ML-126510 ML-126512 ML-126514 VW1DB VW2DB VW3DB VW4DB R-SERIES: VW1D VW2D VW3D VW4D ML-12
VW, VSL & VCW SERIES F-31086 (02-15) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD STARTUP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITYOF THIS OR ANY OTHER APPLIANCE. Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
VW, VSL & VCW SERIES F-31086 (02-15) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VW, VSL & VCW SERIES F-31086 (02-15) GENERAL INTRODUCTION It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions provided. Vulcan-Hart Drawer Warmers and Chip Warmers are produced with quality workmanship and material. Proper installation, usage, and maintenance of your warmer will result in many years of satisfactory performance.
VW, VSL & VCW SERIES F-31086 (02-15) TRIM KIT INSTALLATION 3. Models: VW1SB, VW2SB, VW3SB, VW4SB, VW1CB, VW2CB, VW1DB, VW2DB, VW3DB, VW4DB Built-in Drawer Warmers come with a “trim kit.” Follow the general installation instructions in the “Installation & Operation Manual” regarding Unpacking, Electrical Requirements, Cleaning, and Removal of Vinyl Protection Film. 1. Remove the drawer assemblies from the cabinet. a. Open drawer to full extension. b. Lift up drawer and pull out slightly.
VW, VSL & VCW SERIES F-31086 (02-15) ELECTRICAL REQUIREMENTS : All warmers are equipped with a three-prong plug. It is imperative that this plug must be connected into a properly grounded three-prong receptacle. If the receptacle is not the proper grounding type, contact an electrician. Do not remove the grounding prong from this plug. ELECTRICAL CODES & STANDARDS: The warmer must accordance with: be installed in In the United States of America: 1. State and Local Codes. 2.
VW, VSL & VCW SERIES F-31086 (02-15) OPERATION POWER LIGHT CONTROLS The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. The warmer Control Panel contains an operating indicator light and a full range thermostat. (Fig.2) THERMOSTAT DIAL: The thermostat also acts as the On/Off switch to the warmer system. Turning the thermostat counter clock-wise until it stops will turn the warmer off.
VW, VSL & VCW SERIES F-31086 (02-15) The thermostat setting is from 1 to 10. A chart of the thermostat setting and approximate temperatures is below. (Fig. 4) The thermometer will begin to move and indicate the interior temperature of the drawer. (Fig. 3) Thermostat Setting 1 2 3 4 5 6 7 8 9 10 (Fig. 3) Approximate Temperature 100⁰F (37⁰C) 110⁰F (43⁰C) 120⁰F (49⁰C) 130⁰F (54⁰C) 140⁰F (60⁰C) 150⁰F (66⁰C) 160⁰F (71⁰C) 170⁰F (77⁰C) 180⁰F (82⁰C) 190⁰F (88⁰C) (Fig.
VW, VSL & VCW SERIES F-31086 (02-15) CLEANING electrical cleaning. power Always supply STAINLESS STEEL CARE unplug before CLEANING: Stainless Steel contains 70 – 80% iron, which will rust if not properly maintained. Stainless Steel also contains 12 – 30% chromium, which forms an invisible passive, protective film that shields against corrosion. The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. DAILY: 1. Unplug electrical power supply. 2.
VW, VSL & VCW SERIES F-31086 (02-15) HEAT TINT: Darkened areas, called “heat tint,” may appear on stainless steel exposed to excessive heat. Excessive heat causes the protective film to thicken. This is unsightly, but is not a sign of permanent damage. PRESERVING & RESTORING: Special stainless steel polishing cleaners can preserve and restore the protective film.
VW, VSL & VCW SERIES F-31086 (02-15) TROUBLESHOOTING SYMPTOMS POSSIBLE CAUSES Warmer not operating REMEDY Warmer not connected to power source. Connect cabinet to power source. No power Check Circuit Breaker and/or check GFCI switch on outlet. GFCI or Ground Fault Circuit Indicator tripped Moisture problem. Shorted element Pinched/damaged wire. Damaged power cord. Dry moisture problem. Contact Authorized Service Provider. Contact Authorized Service Provider. Contact Authorized Service Provider.
VW, VSL & VCW SERIES F-31086 (02-15) 11
VW, VSL & VCW SERIES F-31086 (02-15) 12
