Installation & User Guide

ManualsBrandsVTS ManualsHVACDigital Control Panel for All WING EC Air Curtains

HMI WING UL (1-4-2801-0223), Rev 17

HMI WING UL (1-4-2801-0223)

Installation and operating instructions

Summary of content (8 pages)

PAGE 1
HMI WING UL (1-4-2801-0223), Rev 17 HMI WING UL (1-4-2801-0223) Installation and operating instructions
PAGE 2
Table of Contents 1. Important information for installers and final users................................................................................................................................. 1 2. Manufacturer information ...................................................................................................................................................................... 1 3. The purpose of the HMI WING UL (1-4-2801-0223) ............................................................
PAGE 3
HMI WING UL (1-4-2801-0223), Rev 17 1. IMPORTANT INFORMATION FOR INSTALLERS AND FINAL USERS  This controller should be:  Installed only by qualified personnel in accordance with local and national regulations. Proper installation is intended to care of the Class II requirements (reinforced insulation) to prevent electric shock hazard.  Mounted properly as described in the manual, so the casing or enclosure is only accessible to the end user and protection against electric shock is assured. 2.
PAGE 4
HMI WING UL (1-4-2801-0223), Rev 17 5.1. CONNECTION OF HMI WING UL CONTROLLER TO WING W100/150/200 240/1/60 MODELS Connect the HMI WING UL to the WING W100/150/200 air curtains according to diagram shown on Figure 2. Figure 2 - WING W100/150/200 connections 5.2. CONNECTION OF HMI WING UL CONTROLLER TO WING E100 240/1/60 MODEL. Connect the HMI WING UL to the WING E100 240/1/60 air curtains according to diagram shown on Figure 3. Figure 3 - WING E100 240/1/60 connections 5.3.
PAGE 5
HMI WING UL (1-4-2801-0223), Rev 17 5.4. CONNECTION OF HMI WING UL CONTROLLER TO WING E100/150/200 480/3/60 MODELS. Connect the HMI WING UL to the WING E100/150/200 480/3/60 air curtains according to diagram shown on Figure 5. Figure 5 - WING E100/150/200 480/3/60 connections. 5.5. CONNECTION OF HMI WING UL CONTROLLER TO WING C100/150/200 240/1/60 MODELS. Connect the HMI WING UL to the WING C100/150/200 240/1/60 air curtains according to diagram shown on Figure 6.
PAGE 6
HMI WING UL (1-4-2801-0223), Rev 17  Power supply wires o 2 x 18 AWG o Temperature of the wire insulation: 176 °F (80 °C)  Heating stages control wires (H1, H2)  Fan revolutions 0-10 control wires o 2 x 18 AWG o Temperature of the wire insulation: 176 °F (80 °C)  Door switch wires o 2 x 18 AWG o 2 x 20 AWG o Temperature of the wire insulation: 176 °F (80 °C) o Temperature of the wire insulation: 176 °F (80 °C) 6. OPERATIONS ON THE HMI WING UL 6.1.
PAGE 7
HMI WING UL (1-4-2801-0223), Rev 17 6.4. MAIN SETTINGS No. Description Operation button Temperature display: ROOM (current temp.), SET (set temp.
PAGE 8
HMI WING UL (1-4-2801-0223), Rev 17 Modes of automatic operation: A0 room [0], door [1], door+room [2] selection [0, 1, 2] A9 Backlight time 5….600s AA Door optimum 0, +1, +2, +3 AB Door sensor logic NO [0], NC [1] Regulation of the heating power level: A1 without heating [0], first level [1], second level [2], third level [3] Selection [0, 1, 2, 3] A2 Temp. sensor calibration max. ±8°C with the step of 0.5°C AC Selection [0, 1, 2] AD Min.