Introduction IMPORTANT: The VT2420 is an Accessory Handset for use with the VT2431 GIGAPHONE system. You must have the VT2431 in order to use the VT2420 Accessory Handset. This manual is designed to familiarize you with the VT2420 Accessory Handset setup, registration and basic functions. For detailed operational instructions, please refer to the VT2431 manual. To order additional system Handsets (model# VT 2420), battery packs, or headsets, call VTech Communications Inc at 1-800-595-9511.
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. 2. 3. Read and understand all instructions. 4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6.
12. Unplug this product from the wall outlet and refer servicing to a VTECH authorized service facility under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions.
Getting Started Setup Registration And Operation Of The VTECH VT2420 Accessory Handset Your VTECH GIGAPHONE system can operate up to 4 Handsets. The VTECH accessory Handset consists of the following: Belt Clip Handset Battery Pack Charger Unit Setup Of The VT2420 Accessory Handset 1 1. Plug the AC power adapter into an electrical outlet. 2. Remove the Handset battery cover by pressing on the indent and sliding downward. 3.
Follow the steps below: 1 3 1. Remove the battery cover by pressing on the indent and sliding downward. 2. Place the new battery pack in the handset with the metal contacts aligned with the charge contacts in the battery compartment. 3. Replace the battery cover by sliding it upwards. 4. If the new battery pack is not already charged, place the handset in the base unit, or a remote charging stand, and allow it to charge for 12 hours.
Getting Started Registration Enter Base ID Code 1. After charging the Handset, remove it from its Charge Cradle, the screen will display: 2. Press NEW, then enter the 15 digit Base Unit ID code, located on the underside of the Base Unit. 3. Press OK. The Handset will display: PLEASE WAIT!! 4. Wait approximately 15 seconds. The Handset will display: FOUND BASE If the Handset displays: BASE BUSY TRY LATER, this indicates that the system is in use.
1 2 3 9 4 10 5 6 11 7 12 8 13 14 1. 2. 3. 4. 5. 6. 7. 8. Handsfree Speakerphone 9. LCD Display 10. Select 11. Off (Clear) 12. Battery Compartment 13. Intercom 14. Microphone Antenna Message Waiting Indicator Earpiece Headset Jack (2.
Handset Indicators Handset Icons Description Icon Line In Use indicator On steady with no number next to it when a parallel set is in use. On steady with one or more numbers next to it, indicating which extensions are using the line. For example, 12 indicates that Handset 1 and Handset 2 are on an outside call. Handset Operation Intercom indicator On steady with the extension numbers currently on an intercom call. For example, 02 indicates that the Base and Handset 2 are on an intercom call.
Headset Operation Your GIGAPHONE cordless telephone is equipped with a 2.5mm Headset Jack for use with an optional accessory Headset for hands-free operation. If you choose to use the Headset option, you must obtain an optional accessory Headset, which is compatible with the GIGAPHONE. To purchase a Headset, call VTECH Customer Service at 1-800-595-9511. Once you have a compatible 2.5mm Headset, locate the Headset Jack on the GIGAPHONE Handset.
Maintenance Taking Care Of Your Telephone Your GIGAPHONE cordless telephone contains sophisticated electronic parts, so it must be treated with care. Avoid rough treatment Place the Handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it. Avoid water Your telephone can be damaged if it gets wet. Do not use the Handset outdoors in the rain, or handle it with wet hands. Do not install your Base Unit near a sink, bathtub or shower.
In Case Of Difficulty If you have difficulty operating your phone, the suggestions below should solve the problem. If you still have difficulty after trying these suggestions, call VTECH Communications at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800267-7377. The Phone Doesn't Work At All • • • Make sure the Power Cord is plugged Make sure the telephone line cord is plugged firmly into the Base Unit and the telephone wall jack. Make sure the batteries are properly charged.
In Case Of Difficulty You Hear Other Calls While Using Your Phone • Disconnect your Base Unit from the telephone jack, and plug in a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company. You Hear Noise In The Handset, And None Of The Keys Or Buttons Work • Make sure the power cord is plugged in.
Warranty Statement WHAT DOES OUR WARRANTY COVER? • Any defect in material or workmanship. FOR HOW LONG AFTER THE ORIGINAL PURCHASE? • To the original purchaser only - ONE YEAR. WHAT WILL VTECH DO? • At our option, repair or replace your unit. VTECH COMMUNICATIONS INC. 11035 SW 11th STREET BDLG. B, SUITE 270 BEAVERTON, OREGON 97005 If you purchased your phone in Canada, Ship the unit via UPS insured, or equivalent to: VTECH ELECTRONICS LTD. SUITE 200-7671 ALDERBRIDGE WAY RICHMOND,B.C.
Warranty Statement WHAT DOES OUR WARRANTY NOT COVER? • • • • • • • Batteries Damage from misuse, neglect, or acts of nature (lightning, floods, power surges, etc.) Products which may have been modified or incorporated into other products Products purchased and/or operated outside the USA, its territories, or Canada.
FCC and IC Regulations This equipment complies with Parts 15 of the Federal Communications Commission (FCC) rules for the United States. It also complies with regulations RSS210 and CS03 of Industry and Science Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC and IC Regulations FCC Part 68 The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC RJ11C, RJ11W or RJ14). Your telephone company may discontinue your service if your equipment causes harm to the telephone network. They will notify you in advance of disconnection, if possible. During notification, you will be informed of your right to file a complaint with the FCC.
FCC and IC Regulations Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of services in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier.
Technical Specifications FREQUENCY CONTROL WEIGHT Crystal controlled PLL synthesizer Handset : Charger : TRANSMIT FREQUENCY POWER REQUIREMENTS 2401.056 - 2481.408 MHz 185 grams 200 grams Handset : 2.4 VDC NiMH Battery Pack Charger : 6 VDC @ 300mA RECEIVE FREQUENCY 2401.056 - 2481.408 MHz CHANNELS MEMORY 94 Channels NOMINAL RANGE Speed Dial: 50 Memory locations, into 32 digits per location. EFFECTIVE CID : Maximum power allowed by FCC and IC.
Table Of Contents 1. Introduction 2. Important Safety Instructions 4. Getting Started 4. Setup 5. Installation of Battery Pack in Handset 6. Registration 7. The Handset layout 8. 8. 9. Handset Operation Handset Indicators Additional Information 9. Headset Operation 10. Maintenance 11. In Case Of Difficulty 13. Warranty Statement 15. FCC and IC Regulations 18.
VTECH TELECOMMUNICATIONS LTD. A member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTech Communications Inc, 11035 SW 11th Street, Bdlg. B, Suite 207, Beaverton, Oregon, 97005 Distributed in the Canada by VTech Electronics Canada Ltd., Suite 200-7671 Alderbridge Way Richmond, B.C. V6X 1Z9. Copyright 2000 for VTECH TELECOMMUNICATIONS LTD.
ACCESSORY HANDSET FOR USE WITH VT2431 SYSTEM 2420 ACCESSORY HANDSET USER'S MANUAL VTECH TELECOMMUNICATIONS ITD. WWW.vtechphones.