User`s manual
Quick start guide
for model LS6245
Install the telephone base
Install the telephone base as shown below.
Battery installation and charging
Install the battery as shown below. For optimal
performance, charge the handset battery for at least 16
hours before use.
Pair your rst Bluetooth cell phone
To pair and connect your rst Bluetooth cell phone:
Press the MENU softkey on the
telephone base.
Press /VOL
+
or VOL
-
/ to
highlight Bluetooth, then press
the SELECT softkey.
Press /VOL
+
or VOL
-
/ to
highlight Setup cell, then press
the SELECT softkey.
Press the NEXT softkey to
set the telephone base in
discoverable mode.
Turn on the Bluetooth feature of
your cell phone and search for
or add new devices.
Once your cell phone nds
VTech LS6245, select it.
Enter the telephone base PIN
(the default PIN is 0000) into
your cell phone.
When successfully connected,
Device connected to base
displays.
1.
2.
3.
4.
5.
6.
7.
8.
Use only the power adapter and battery supplied
with your VTech telephone.
For complete feature instructions, please refer to
your user’s manual.
1.
2.
Pair your rst Bluetooth headset
To pair and connect your rst Bluetooth headset:
Telephone line cord
DSL filter (not
included) is
required if you
have DSL high
speed Internet
service
Telephone
base power
adapter
Electrical outlet
not controlled
by a wall switch
Telephone wall jack
Telephone base
If the battery
compartment cover
is on the handset,
press on the triangle
and slide the cover to
remove.
1. Plug the battery
connector securely
into the socket
inside the handset
battery compartment,
matching the color-
coded label.
2.
Place the battery with
the label THIS SIDE
UP facing up and the
wires inside the battery
compartment.
3. Align the cover at
against the battery
compartment, then
slide it towards the
center of the handset
until it clicks into place.
4.
Charge the handset
by placing it in the
telephone base. The
CHARGE light is on
when the handset
charges.
5.
CHARGE light
Setup cell
Setup headset
Active devices
SELECT
Page all HS
Intercom
Bluetooth
SELECT
Pls set your
cell to search
for devices
NEXT
LS6245
discoverable
PIN:0000
Pairing
complete
BASE
2:22pm 12/25
MENU
REDIAL
Device
connected
to base
Press the MENU softkey on the
telephone base.
Press /VOL
+
or VOL
-
/ to
highlight Bluetooth, then press
the SELECT softkey.
Press /VOL
+
or VOL
-
/ to
highlight Setup headset, then
press the SELECT softkey.
Set your headset to
discoverable mode.
Press the NEXT softkey on the
telephone base to search for
your headset.
Once the telephone base
nds your headset, press the
SELECT softkey.
Enter the PIN of your headset
(the PIN for most Bluetooth
devices is 0000), then press
the NEXT softkey. The screen
displays Headset setup
complete.
When the base displays
Connect headset to base?,
press the YES softkey.
When successfully connected,
Device connected to base
displays.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Page all HS
Intercom
Bluetooth
SELECT
BASE
2:22pm 12/25
MENU
REDIAL
Pls set headset
to discoverable
mode
NEXT
Searching
for headset
Headset setup
complete
Connect headset
to base?
NO
YES
Device
connected
to base
SELECT HEADSET
Mary’s Headset
SELECT
ENTER PIN
----
NEXT
Setup cell
Setup headset
Active devices
SELECT
The pairing process may take
up to one minute. If the pairing
process fails, try again.
The pairing process may take
up to one minute. If the pairing
process fails, try again.