User Guide

58
59
NOTES
• The pairing process may take up to
one minute. If the pairing process
fails, try again.
• The steps for the pairing process may
vary for different cell phones. If this
happens, follow the prompts on your
cell phone and your IS8121-2/IS8121-
3/IS8121-4/IS8121-5 to complete the
pairing process.
• Refer to the user’s manual of your cell
phone on how to search for or add a
new Bluetooth device.
Add a Bluetooth headset
Before you begin, make sure that
your Bluetooth enabled headset is
not connected to any other Bluetooth
device. Refer to your headset user’s
manual to learn how to search for or add
new Bluetooth devices.
Pair and connect a headset
1. Press MENU/SELECT on the handset
in idle mode.
2. Press q CID or p to highlight
Bluetooth, then press MENU/SELECT.
3. Press q CID or p to highlight
Add BT headset, then press
MENU/SELECT.
• The display shows Search
headset...
4. Set your headset to discoverable
mode (refer to the user’s manual
of your headset). When the screen
displays the found devices, press
q CID or p
to highlight your
headset, if necessary, then press
MENU/SELECT.
NOTES
• The pairing process may take up to
one minute. If the pairing process
fails, try again.
• When a connected headset is
charging, it may disconnect from the
telephone base and the CELL 2 light
on the telephone base turns off. For
some headset models, you may need
to turn on the headset and reconnect
it to the telephone base again.
Device list and connection
Up to two devices can be paired to the
telephone base. All paired devices are
shown on the device list. To use a paired
device, it must be connected and in an
active slot (1: or 2:) on the device list.
Only one active device can be on a call
at a time.
Once you have paired a device with
the telephone base, you do not need
to repeat the pairing procedure again
unless you delete the device from the
device list.
NOTE
• When connecting a Bluetooth device
to the device list, all connected devices
will be temporarily disconnected until
the procedure is complete. It may take
up to two minutes to reconnect.
Review the Bluetooth device list
1. Press MENU/SELECT on the handset
in idle mode.
2. Press q CID or p to highlight
Bluetooth, then press MENU/
SELECT.
3. Press MENU/SELECT again to select
Device list.
Download/Transfer your cell phone
phonebook entries via Bluetooth
You can download cell phone
phonebook entries to your IS8121-2/
IS8121-3/IS8121-4/IS8121-5 telephone
system via Bluetooth wireless
technology. Each downloaded cell
phone phonebook entry is stored in
the handset phonebook with up to 24
digits for each phone number and 15
characters for each name.
Before downloading the cell phone
phonebook, make sure the cell phone
is paired, active, and connected to your
IS8121-2/IS8121-3/IS8121-4/IS8121-
5. Make sure the handset battery is
charged for at least 10 minutes.
Place your cell phone next to the
telephone base when you download a
cell phone phonebook to your IS8121-
2/IS8121-3/IS8121-4/IS8121-5.
Download a cell phonebook
1. Press MENU/SELECT on the handset
in idle mode.
2. Press q CID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press q CID or p to highlight
Download DIR, then press
MENU/SELECT.
• The handset displays Select a
device briefly.
• If there is no cell phone paired to
the system, the handset displays
Pair cell first and then returns to
the previous menu.
4. Press q CID or p to choose a
desired device when necessary, and
then press MENU/SELECT.
• If the selected device is not
available, the handset returns to
the previous menu.
• During the download, the
handset flashes Downloading....
All other idle system handsets
display Downloading.....
• When the downloading process
completes or when the memory
is full, the handset displays Entries
added: XXX. Then, the handset
returns to the Bluetooth menu.