User’s Manual Traffic Signal Bridge © 2013 VTech Printed in China 91-002686-008
Dear Parent, Welcome to the world of Go! Go! Smart Wheels™! We’re excited you’ve decided to ride along with us and explore all that Go! Go! Smart Wheels™ has to offer. These toys have been designed to give your child a thrilling learning experience with hours and hours of fun as well. Go! Go! Smart Wheels™ features vehicles that interact with your child by lighting up, singing and talking, while teaching your child letters and vehicle names (each sold separately).
INTRODUCTION Thank you for purchasing the VTech® Go! Go! Smart WheelsTM Traffic Signal Bridge learning toy! ON/OFF BUTTON 2 TRAFFIC LIGHTS TRAFFIC CONE BUTTON LIFT-UP GATE 2 SMARTPOINTTM LOCATIONS RECOGNITION SENSOR Introduction This playset comes with one traffic light, six track pieces, and a bridge that can be reconfigured and connected with other Go! Go! Smart WheelsTM playsets.
INCLUDED IN THIS PACKAGE One VTech® Go! Go! Smart WheelsTM Traffic Signal Bridge. six track pieces • 1 bridge 1 traffic light One user’s manual WARNING: All packing materials, such as tape, plastic sheets, packaging locks and tags are not part of this toy, and should be discarded for your child’s safety. ATTENTION ! Pour la sécurité de votre enfant, débarrassezvous de tous les produits d’emballage tels que rubans adhésifs, feuilles de plastique, attaches et étiquettes. Ils ne font pas partie du jouet.
GETTING STARTED 1. Make sure the unit is turned OFF. 2. Locate the battery cover on the bottom of the Go! Go! Smart WheelsTM Traffic Signal Bridge. Use a coin or a screwdriver to loosen the screw. 3. Install 2 new ‘AA’ (LR6/AM-3) batteries following the diagram inside the battery box. (The use of new alkaline batteries is recommended for maximum performance.) 4. Replace the battery cover and tighten the screw to secure.
PRODUCT FEATURES 1. ON/OFF BUTTON To turn the unit ON, press the ON/OFF BUTTON. To turn the unit OFF, press and hold the ON/OFF BUTTON for 0.5 seconds. The traffic light can be turned 180 degrees. You will hear a click sound when it is turned to the correct position in front of the gate. 3. AUTOMATIC SHUT-OFF To preserve battery life, the VTech® Go! Go! Smart WheelsTM Traffic Signal Bridge will automatically power-down after approximately 45 seconds without input.
3. Press the traffic cone button to hear music and sing-along songs. The lights will flash with the sounds. 5. Push a vehicle over the recognition sensor to hear a greeting specific to the vehicle. The lights will flash with the sounds. (The vehicle must be facing the same direction as the arrow.) Activities 4. Flip the gate to hear driving phrases and sounds. The lights will flash with the sounds. 6. Press the button near the recognition sensor to hear fun sounds and short tunes.
. If there is no input to the unit after approximately 4 seconds, you will hear a friendly voice. If there is still no input after another 4 seconds, you will hear another friendly voice. If there is still no input after 4 seconds, you will hear another sing-along song. If there is still no input after a further 4 seconds, then the unit will automatically power down. 1. 2. 3. 4. 5. 6. 7. 8. 9.
TROUBLESHOOTING If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, and a service representative will be happy to help you. For information on this product’s warranty, please call VTech® at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada. IMPORTANT NOTE: Creating and developing Infant Learning products is accompanied by a responsibility that we at VTech® take very seriously.
communications. However, there is no guarantee that interference will not occur in a particular installation.
