User’s manual www.vtechphones.
Congratulations on purchasing your new VTech product. Before using this telephone, please read the Important safety instructions on page 52 of this manual. This manual has all the feature operations and troubleshooting necessary to install and operate your new VTech telephone. Please review this manual thoroughly to ensure proper installation and operation of this innovative and feature rich VTech product. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
Table of contents Getting started . . . . . . . . . . . . . . . . . . 1 Find handset . . . . . . . . . . . . . . . . . . . 14 Parts checklist . . . . . . . . . . . . . . . . . . . 1 Intercom . . . . . . . . . . . . . . . . . . . . . 15 Telephone base and charger installation . . . . . 2 Conference call . . . . . . . . . . . . . . . . . 16 Battery installation and charging . . . . . . . . .
Table of contents Call log display screen messages . . . . . . . . 33 Redial list . . . . . . . . . . . . . . . . . . . . 34 Dial a redial entry . . . . . . . . . . . . . . . . 34 Delete from redial . . . . . . . . . . . . . . . . 34 Answering system . . . . . . . . . . . . . . . 35 Answering system and voicemail . . . . . . . . 35 Message capacity . . . . . . . . . . . . . . . .
Parts checklist Your telephone contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. 2. Handsets 3. Telephone base with mounting bracket (2 for DS6121-2, 3 for DS6121-3, 4 for DS6121-4, 5 for DS6121-5/DS6122-5) 5. Battery compartment covers (2 for DS6121-2, 3 for DS6121-3, 4 for DS6121-4, 5 for DS6121-5/ DS6122-5) 6. Batteries (2 for DS6121-2, 3 for DS6121-3, 4 for DS6121-4, 5 for DS6121-5/ DS6122-5) 4.
Getting started Telephone base and charger installation • Use only the power adapter supplied with this product. To order a replacement, visit our website at www.vtechphones. com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada. com or call 1 (800) 267-7377. • The power units are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under-the-table/ cabinet outlet.
Battery installation and charging Charge light 1 2 3 www.vtechphones.com • If the handset will not be used for a long time, disconnect and remove the battery to prevent possible leakage. • To purchase replacement batteries, visit our website at www. vtechphones. com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada. com or call 1 (800) 267-7377. 4 Basic operation Install the battery as shown below. After installing the battery, you might be able to make and receive short calls.
Getting started Mounting bracket installation Your telephone base comes with the mounting bracket installed for desktop use. If you prefer to mount your telephone on the wall (optional), it is designed to mount on a standard telephone wall plate. Wall mounting bracket installation: 1. Slide the bracket down and away from the telephone base. 2. Tilt the top of the bracket down so that it rests on the base. Align the grooves on the bracket with the tabs on the base. See image 2 below. 3.
Getting started Getting started Mounting bracket installation (continued) 1 3 2 Basic operation Desktop/tabletop bracket installation: Your telephone comes ready for desktop use. If you have repositioned the bracket for wall mounting and now want to return to desktop use, follow the following steps: 1. Remove the bracket from wall mount orientation by sliding it up towards the top of the base. 2. Tilt the top of the bracket up so that the lower portion of the bracket rests on the base. See image 2. 3.
Getting started Handset layout MUTE/REMOVE • While on a call, press to mute microphone. • While reviewing the call log, press to delete an individual entry, or press and hold to delete the entire call log. • Press to delete digits when predialing (preview numbers before dialing). Charge light • On when the handset is charging in the telephone base or charger. INT (intercom) • Press to initiate an intercom conversation or transfer a call.
Telephone base layout Message window • Shows the status and number of messages (page 45). X/DELETE • Press to delete message currently playing (page 42). • Press t wice to delete all old messages when the telephone is not in use (page 43). /REPEAT • Press to repeat a message or press twice to play back previous messages (page 42). Getting started Getting started /SKIP • Press to skip to the next message (page 42). /PLAY/STOP • Press to play or stop messages (page 42).
Telephone settings Ringer volume (handset) • The ringer will be off if the volume is set to the lowest level, and a ringer off icon will be displayed. You can change the ringer volume to a comfortable level. The ringer can also be turned off so the telephone does not ring when there are incoming calls. To adjust the ringer volume: 1. Press VOL or VOL to select the desired ringer volume when the handset is not in use. 2. When you stop pressing the volume buttons, the setting will be saved. -OR1.
Telephone settings This menu allows you to choose from different ringer tones. To choose a ringer tone: 1. Press MENU/SELECT to display the menu when the handset is not in use. 2. Press or to select >RINGER TONE, then press MENU/SELECT. 3. Press or to select the desired ringer tone. A sample of each ringer tone will be played when scrolling through the choices. 4. Press MENU/SELECT to confirm your selection. You will hear a confirmation tone. www.vtechphones.
Telephone settings Key tone The handset will beep when you press any handset key. You may turn the key tone on or off. To change the setting: 1. Press MENU/SELECT to display the menu when the handset is not in use. 2. Press or to select > KEY TONE, then press MENU/SELECT. 3. Press or to choose ON or OFF. 4. Press MENU/SELECT to confirm your selection. You will hear a confirmation tone. >KEY TONE LANGUAGE KEY TONE ON Language You can select ENGLISH, FRANÇAIS or ESPAÑOL to be used in all screen displays.
Telephone settings If you subscribe to voicemail service offered by your telephone service provider, NEW VOICE MAIL and will appear on the handset, and the VOICEMAIL light on the telephone base will flash when you have new voicemail messages. Please contact your local telephone company for more information and assistance about using your voicemail service. After you have listened to all new voicemail messages, the indicators on both the handset and telephone base will be turned off automatically.
Telephone operation Make a call • The screen displays the elapsed time as you talk (in hours, minutes and seconds). • When predialing (preview numbers before dialing), press MUTE/REMOVE or OFF/CLEAR to backspace and delete; press and hold REDIAL/PAUSE to insert a dialing pause. 1. Press /FLASH or 2. Dial the number. -OR1. Dial the number. 2. Press /FLASH or /SPEAKER /SPEAKER.
Telephone operation Mute Ringer mute You can mute the ringer temporarily when the telephone is ringing. • Press OFF/CLEAR or MUTE/REMOVE to temporarily silence the ringer. The next call will ring normally. PHONE MUTED Basic operation Telephone operation The mute function allows you to hear the other party while the other party cannot hear you. 1. During a call, press MUTE/REMOVE on the handset. MUTED will be temporarily displayed on the screen, along with the smaller MUTE icon. 2.
Telephone operation Chain dialing • Chain dialing can be useful if you wish to access numbers other than phone numbers (such as bank account information or access codes) from the directory, call log or redial list. This feature allows you to initiate a dialing sequence from numbers stored in the directory, call log or redial list while you are on a call. To access a number in the directory: 1. Press MENU/SELECT twice to enter the directory menu. 2. Scroll by pressing or to find the desired entry. 3.
Telephone operation Intercom www.vtechphones.com CALLING OTHER HANDSET OTHER HANDSET IS CALLING INTERCOM TO: • If the destination handset does not answer the intercom call within 100 seconds, is in the directory, is in the call log, is on a call, or out of range, the originating handset screen will display UNABLE TO CALL TRY AGAIN and return to idle mode.
Telephone operation Conference call You can have a conference call with an external line and two registered handsets. When one handset is on the line, • Press /FLASH or /SPEAKER on another handset to join the call. -ORModel DS6121-2 1. Press INT to initiate an intercom call and its screen displays CALLING OTHER HANDSET. The destination handset rings and its screen displays OTHER HANDSET IS CALLING. 2.
Telephone operation Transfer an external call www.vtechphones.com • If the destination handset does not pick up the intercom call, the originating handset can return to the external call by pressing /FLASH, OFF/CLEAR or INT. • If a call remains on hold for about 100 seconds, or if the destination handset is in the directory, in the call log, or out of range, the screen of the originating handset shows UNABLE TO CALL TRY AGAIN and reconnects to the external call automatically.
Telephone operation 18 Models DS6121-3/DS6121-4/DS6121-5/DS6122-5 1. During a call, press INT to put the call on hold at the TRANSFER TO: originating handset. The screen displays TRANSFER TO: 2. Use the dialing keys to enter the destination handset number. The originating handset screen displays CALLING CALLING HANDSET X. HANDSET X 3. The destination handset rings and its screen displays HANDSET X IS CALLING. HANDSET X 4.
Telephone operation Switch between external and intercom call www.vtechphones.com Basic operation Telephone operation If you are on an external call and you wish to intercom another handset without disconnecting the external call: Model DS6121-2 1. During a call, press INT to put the call on hold at the originating handset. Its screen displays CALLING OTHER HANDSET. 2. The destination handset will ring and its screen will display OTHER HANDSET IS CALLING. 3.
Telephone operation Models DS6121-3/DS6121-4/DS6121-5/DS6122-5 1. During a call, press INT to put the call on hold at the originating handset. The screen displays TRANSFER TO: 2. Use the dialing keys to enter the destination handset number. The originating handset screen displays CALLING HANDSET X. 3. The destination handset will ring and its screen will display HANDSET X IS CALLING. 4.
Telephone operation Directory DIRECTORY EMPTY Basic operation Telephone operation The directory can store up to 50 entries. Each entry may have up to 30 digits for the phone number and 15 characters for the name. • The directory can be accessed when the handset is not in use by pressing once or MENU/SELECT three times. • The screen displays DIRECTORY EMPTY if there are no records in the directory. • When the directory is full and you attempt to save an entry, the screen will display LIST FULL.
Telephone operation Store a directory entry • Saving or deleting a number on one handset will automatically update all other handsets. 22 1. Press MENU/SELECT twice when the handset is not in use. 2. Press or to select >STORE, then press MENU/SELECT. The screen displays ENTER NUMBER. 3. Use the dialing keys to enter the number. • Press MUTE/REMOVE to backspace and erase a digit. • Press and hold MUTE/REMOVE to erase the entire entry. • Press to move the cursor to the left or to the right.
Telephone operation Character chart Use the dial pad and the chart below to enter a name (up to 15 characters). Each press of a particular key causes the characters to be displayed in the following order: Number key Characters by number of key presses 1 2 4 5 6 7 1 1 # , - .
Telephone operation Search the directory Entries are sorted alphabetically. To search the directory: 1. Press once or MENU/SELECT three times to enter the directory. 2. Press or to scroll through the directory. >REVIEW STORE VTECH 800-595-9511 To start an alphabetical search: 1. Press once or MENU/SELECT three times to enter the directory. 2. Use the dialing keys to enter the first letter associated with the name.
Telephone operation Edit a directory entry www.vtechphones.com Basic operation Telephone operation 1. Press once or MENU/SELECT three times to enter the directory. 2. Press or to scroll to the desired entry, or use the alphabetical search to find it. 3. Press MENU/SELECT to confirm your selection. The EDIT NUMBER screen displays EDIT NUMBER. 595-9511_ 4. Use the dialing keys to edit the number. • Press MUTE/REMOVE to backspace and erase a digit. • Press and hold MUTE/REMOVE to erase the entire entry.
Telephone operation Delete from the directory 1. Press once or MENU/SELECT three times to enter the directory. 2. Press or to scroll to the desired entry, or use the alphabetical search to find it. 3. Press MUTE/REMOVE to remove the desired entry. You will hear a confirmation tone. 26 www.vtechphones.
Telephone operation About caller ID www.vtechphones.com Basic operation Telephone operation The caller ID with call waiting feature in this telephone lets you see the name and telephone number of the caller before answering the call, even when you’re on a call. These features require services provided by your local telephone company.
Telephone operation Call log • Due to regional service differences, the caller ID information may not be available for every incoming call. In addition, the callers may intentionally block their names and/or telephone numbers. • For call log entries with numbers between 16 and 23 digits, in order to view the entire number you must save the entry to the directory. For information on saving call log entries to the directory, see page 31.
Telephone operation Missed calls indicator Review the call log 1. Press CID when the handset is not in use. 2. Press or to browse through the call log. -OR1. Press MENU/SELECT when the handset is not in use. 2. Press or to select >CALL LOG. 3. Press MENU/SELECT. 4. Press or to browse through the call log. • The name (if available), telephone number, date and time of all incoming calls are displayed on the screen. • There will be an error tone when the list reaches the beginning or end of the call log.
Telephone operation Make a call log entry ready to dial Although the call log entries received have 10 digits (the area code plus the seven-digit number), in some areas, you may need to dial only the seven digits, or a 1 plus the seven digits, or a 1 plus the area code plus the seven digits. You can change the number of digits that you dial from or store in the call log.
Telephone operation Save a call log entry to the directory SAVED • Saving or deleting a number on one handset will automatically update all other handsets. • See page 25 about editing names and numbers. ALREADY SAVED UNABLE TO SAVE www.vtechphones.com 31 Basic operation Telephone operation 1. When in the call log, press or to scroll to the desired entry. 2. Press MENU/SELECT. • You can edit the phone number, if necessary. Make sure the number is in the correct dialing format for your area.
Telephone operation Delete from the call log To delete one entry: 1. When in the call log, press or to scroll to the desired entry. 2. Press MUTE/REMOVE to delete the selected entry. You will hear a confirmation tone. To delete all entries: 1. When in the call log, press and hold MUTE/REMOVE to delete the entire call log. The screen displays DELETE ALL CALLS? 2. Press MENU/SELECT to confirm. You will hear a confirmation tone.
Telephone operation Call log display screen messages When: PRIVATE NAME The caller is blocking the name information. PRIVATE NUMBER The caller is blocking the telephone number information. PRIVATE CALLER The caller is blocking the name and number information. UNKNOWN NAME This caller’s name is unavailable. Basic operation Telephone operation Displays: UNKNOWN NUMBER This caller’s number is unavailable. UNKNOWN CALLER No information is available about this caller. www.vtechphones.
Telephone operation Redial list The telephone stores the five most recently dialed numbers on the redial list. • When there are already five entries on the redial list, the earliest entry will be deleted to make room for the latest entry. • Entries are displayed in reverse chronological order, i.e. from the latest entry to the earliest entry. The redial list can be accessed by pressing REDIAL when in idle mode. Dial a redial entry 1.
Answering system Answering system and voicemail Basic operation Answering system Your telephone has both a digital answering system and voicemail indication. Voicemail is offered by your telephone service provider (fees may apply). Your telephone’s answering system and voicemail indication are independent features, and each alerts you to new messages differently. For more information on the voicemail indicators, see page 9.
Answering system Activate the answering system • If you have caller ID service, the clock will be set automatically with incoming calls, but you will need to make sure the year is correct. See Set the clock for instructions on how to set the year, time and day manually. • Press and hold /SKIP or /REPEAT while setting the minutes or year to advance or decrease by increments of ten. 36 The answering system must be turned on to answer and record messages.
Answering system 5. Press /SKIP or /REPEAT until the system announces the correct minute, then press CLOCK. The system announces the current day. 6. Press /SKIP or /REPEAT until the system announces the correct day, then press CLOCK. After a confirmation tone, the system announces the new clock setting and exits programming mode. Answering system setup Basic operation Answering system The answering system uses voice prompts to guide you through feature setup.
Answering system Set number of rings (continued) If you subscribe to caller ID/call waiting and voicemail service through your telephone service provider, you can use your telephone answering system and voicemail together. Set your answering system to answer calls at least two rings earlier than your voicemail is set to answer. For example, set your voicemail to answer calls after six rings and set your answering system to answer after four rings.
Answering system Set remote access code • The answering system must be turned on for the message alert tone to function. Basic operation Answering system A two-digit security code is required to access the answering system remotely from any touch tone telephone. The preset code is 19. You can set the code from 10 to 99. To set the remote access code: 1. Press SETUP when the telephone is not in use until the system announces the remote access code setting. 2.
Answering system Outgoing announcement The outgoing announcement is the greeting callers hear when calls are answered by the answering system. The telephone is preset with a greeting that answers calls with “Hello, please leave a message after the tone.” You can use this preset announcement, or replace it with your own. While in the ANNC menu, press ANNC again to exit at anytime. Play your announcement 1. Press ANNC when the telephone is not in use. The system will announce “Announcement.
Answering system Record your own announcement • Your announcement can be up to 90 seconds in length. • Announcements shorter than two seconds will not be recorded. • When your announcement is deleted, calls will be answered with the preset announcement. Delete your announcement 1. Press ANNC when the telephone is not in use and the system will announce “Announcement. Press PLAY or press RECORD.” 2. Press X/DELETE and the system will announce “Announcement deleted.” www.vtechphones.
Answering system New message indication • If the memory is full, the system will answer after 10 rings and announce, “Memory is full. Enter the remote access code.” • If the answering system is off, the system will answer after 10 rings and announce, “Please enter your remote access code.” • If the system has less than five minutes of recording time left, the remaining time will be announced. • If F is flashing in the message window, the memory is full.
Answering system Delete all messages Press X/DELETE when in idle mode. The system will announce “To delete all old messages, press DELETE again.” Press X/DELETE again. All previously heard messages will be erased. Record and play memos Record a memo 1. Press RECORD when in idle mode. The system announces, “Record after the tone. Press STOP when you are done.” 2. After the tone, speak towards the microphone at the bottom front of the telephone base from about nine inches away. 3.
Answering system Call screening You can listen at the telephone base to a caller leaving a message. However, if you want to silence the telephone base when messages are being recorded, set the telephone base volume to its lowest level (1). Remember to raise the volume in order to hear your messages during playback. Call intercept If you want to answer a call while a message is being recorded, press on the handset. 44 www.vtechphones.
Answering system Message window displays Descriptions: 0 No messages. 1-98 Total number of old message(s) recorded. 0-98 (flashing) Total number of new and old message(s) recorded; or the telephone base may have lost and regained power. 99 & F (alternating) Memory is full with total number of messages recorded. 1-99 (counting) Elapsed time while recording memo or announcement (up to 90 seconds). 99 (flashing) Recording time exceeds 99 seconds.
Answering system Remote access • If no key is pressed after entering remote access, new messages will be played automatically. If there are no new messages, all old messages will be played automatically. • Once the new messages have been played, the system will announce the help menu options. If no key is pressed within 20 seconds, the remote access call is automatically disconnected.
Handset display screen messages ALREADY SAVED CALL LOG EMPTY CALLING HANDSET X (for DS6121-3/DS6121-4/DS6121-5/DS6122-5) The telephone number you have entered is already stored in the directory. There are no call log entries. Calling another handset. CALLING OTHER HANDSET (for DS6121-2) CONNECTING... CHARGING DIRECTORY EMPTY ENDED HANDSET X IS CALLING (for DS6121-3/DS6121-4/DS6121-5/DS6122-5) The cordless handset is searching for the telephone base.
Handset display screen messages MICROPHONE ON MUTED NEW VOICE MAIL NO LINE NO SIGNAL, CALL ENDED NOT AVAILABLE AT THIS TIME MUTE has been turned off and the person on the other end can hear you. The microphone is muted temporarily during a conversation. There are new voicemail messages from the local telephone company. There is no telephone line connected. Communication between handset and telephone base is lost during a call.
Handset display screen messages WARNING CHECK BATTERY! XX MISSED CALLS The battery is not installed or not installed properly in the handset. -OR The battery needs to be replaced. -OR An incorrect battery has been installed. Use only the supplied VTech battery or equivalent. There are unreviewed calls in your call log. Handset and telephone base indicators Handset lights • On when the handset speakerphone is in use. • On when the handset is in the telephone base or charger and is charging.
Handset and telephone base indicators Handset icons MUTE • Microphone is muted. • Ringer off. NEW • New call log entries. NEW VOICE MAIL • New voicemail received from the local telephone company. SPEAKER • In speakerphone mode. Battery indicator • Cycles (low, medium, and full) when the handset battery is charging. • Flashes when the battery is low and needs charging. • Displays solid when the battery is fully charged. 50 www.vtechphones.
Battery It takes up to 16 hours for the battery to be fully charged. When it is fully charged, you can expect the following performance: Operation Operating time While in handset use (talking*) Nine hours While in speakerphone mode (talking*) One and a half hours While not in use (standby**) Five days *Operating times are approximate. Your results may vary. **Handset is off the telephone base but not in use. The battery needs charging when: • A new battery is installed in the handset.
Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4.
Troubleshooting If you have difficulty with your telephone, please try the suggestions below. For Customer Service, visit our website at www.vtechphones.com, or call 1 (800) 595-9511; in Canada, call 1 (800) 267-7377. Problem Suggestion My telephone does not work at all. • Make sure the battery is installed and charged correctly (page 3). For optimum daily performance, return the handset to the telephone base or charger after use.
Troubleshooting Problem Suggestion The battery does not charge in the handset or the handset battery is not charging. • Make sure the handset is placed in the telephone base or charger correctly. The CHARGE light on the handset should be on. • Remove and reinstall the battery, then charge for up to 16 hours. • If the handset is in the charger or in the telephone base but the CHARGE light on the handset is not on, refer to The charge light is off in this section.
Troubleshooting Problem Suggestion The telephone does not ring when there is an incoming call. • Make sure the handset ringer volume is not set to zero (page 8) and the telephone base ringer volume is not set to off (page 38). • Make sure the telephone line cord and power adapter are plugged in properly (page 2). • The handset may be too far from the telephone base. Move it closer to the telephone base.
Troubleshooting Problem Suggestion I cannot dial out. • First, try all the above suggestions. • Make sure there is a dial tone before dialing. It is normal if the handset takes a second or two to synchronize with the telephone before producing a dial tone. Wait an extra second before dialing. • If the other telephones in your home are having the same problem, the problem is in the wiring or local service. Contact your local telephone company (charges may apply). • Eliminate any background noise.
Troubleshooting Suggestion There is interference during a telephone conversation. • The handset may be out of range. Move it closer to the telephone base. • Do you have DSL service? If yes, you need to have a DSL filter installed at every telephone wall jack that has a telephone connected to it (page 2). Contact your DSL service provider for filter information. • Appliances or other cordless telephones plugged into the same circuit as the telephone base can cause interference.
Troubleshooting Problem Suggestion I hear noise on the • Make sure the telephone line cord is plugged in securely. cordless handset, and none of the keys or buttons works. My caller ID features are not working properly. • Caller ID is a subscription service. You must subscribe to this service from your local telephone company for this feature to work on your telephone. • The caller may not be calling from an area which supports caller ID.
Troubleshooting Problem Suggestion Caller ID entries do not • Although the call log entries you receive have 10 digits, (the area code plus the seven-digit number), in some areas, you may need to dial only the seven digits, or a 1 plus the seven digits, match the numbers I or a 1 plus the area code plus the seven digits. You can change the number of digits that you need to dial. dial from the call log.
Troubleshooting Problem Suggestion The answering system does not answer after the number of rings to which I programmed it. • Make sure the answering system is on. When the answering system is on, the red light on the ANS ON/OFF key should be lit. • If toll saver is activated, the number of rings changes to two when there are new messages recorded (page 37). • If the memory is full or if the answering system is off, the system will answer after ten rings.
Troubleshooting Problem Suggestion The answering system does not respond to remote commands. • Make sure your remote access code is correct (page 39). • Make sure you are calling from a touch-tone telephone. When dialing a number, there should be tones. If there are clicks, then it is not a touch-tone telephone and cannot activate the answering system. • The answering system may not detect the remote access code when your announcement is playing.
Operating range This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance - which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or office. When the handset is out of range, the handset will display CONNECTING...
About cordless telephones • Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.
Warranty What does this limited warranty cover? The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions.
Warranty 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service? To obtain warranty service in the United States of America, please call 1 (800) 595-9511. In Canada, please call 1 (800) 267-7377. NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.
FCC, ACTA and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation.
FCC, ACTA and IC regulations RJ14 jack for two lines. See Installation Instructions in the user’s manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less.
Technical specifications Frequency control Crystal controlled PLL synthesizer Transmit frequency Handset: 1921.536-1928.448 MHz Telephone base: 1921.536-1928.448 MHz Channels 5 Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Size Handset: 6.61in X 1.77in X 1.06in (168.0mm X 45.0mm X 27.0mm) Telephone base: 6.04in X 4.04in X 4.06in (153.5mm X 102.5mm X 103.0mm) Charger: 2.80in X 3.14in X 2.
Index A D Activate the answering system 36 Answer a call 12 Answer an incoming call during an intercom call 20 Answering system setup 37 B Battery 3, 51 C Call intercept 44 Call log 28 Call log display screen messages Call screening 44 Call waiting 13 Caller ID 27 Chain dialing 14 Character chart 23 Charger installation 2 Charging 3 Clear voice mail 11 Conference call 16 Cordless telephones 63 H Delete messages from answering system 42, 43 Delete from redial 34 Delete from the directory 26 Delete f
Index M Maintenance 62 Make a call 12 Make a call log entry ready to dial Memo playback 43 Message capacity 35 Message playback 42 Message window displays 45 Missed calls indicator 29 Mounting bracket installation 4 Mute 13 N New message indication 42 O Operating range 62 Options during playback 42 Outgoing announcement 40 P Paging 14 Parts checklist 1 Play your announcement 70 40 R 30 RBRC ® seal 63 Record and play memos 43 Record your own announcement Redial list 34 Remote access 46 Review the
VTECH TELECOMMUNICATIONS LTD. A member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon Distributed in Canada by VTech Technologies Canada, Ltd., Richmond, B.C. Copyright ©2008 for VTECH TELECOMMUNICATIONS LTD. Printed in China.
