Owner's manual

24
Analog cordless 1-line/2-line accessory handset - C3100/C3200
Installation
Handset battery installation
Install the battery as shown below.
Gently lift the handset cover. Do not detach the speaker wires between the handset cover and the handset.
Plug the battery connector securely into the socket inside the handset battery compartment.
Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.
To replace the handset cover, align all the tabs on the handset cover against the corresponding grooves on the handset, then
rmly push downward until all the tabs lock in the grooves. Then install the screw.
Replace a handset battery
Use a narrow object to pry open the screw cover and remove the screw. Then insert a 5 mm standard screwdriver in the
provided slot and twist to open the handset cover. Do not detach the speaker wires between the handset cover and the handset.
Unplug the battery connector from the socket and then remove the battery from the handset battery compartment.
Follow Step 2 to Step 4 in Handset battery installation above to install a new battery.
CAUTIONS:
There may be a risk of explosion if a wrong type of handset battery is used. Use only the supplied rechargeable battery (BT264392/BT266342) or
replacement battery (BT266342). To order a replacement, call 1-888-907-2007.
FCC ID is shown on the back of the cordless handset body after the handset cover is removed.
Dispose of used batteries according to the information in The RBRC
®
seal on page 46.
Handset registration
Place the cordless handset on the telephone base cradle. Handset registration happens automatically the rst time a cordless
handset is placed on the telephone base. When the registration process completes, the MESSAGE WAITING LED ashes once and
you hear 3 rising beeps as conrmation. Each telephone base accommodates up to 4 cordless handsets. When you already have
4 registered handsets, you can replace one of them by a new handset if any one of the 4 registered handsets is disconnected from
the base. For example, it is out of range, or its battery is removed or depleted. The previous registered handset is then deregistered
from the telephone base.
Handset deregistration
When a registered cordless handset is idle, press *331734# and then press HOLD. You hear 3 rising beeps as conrmation when
the deregistration process completes.
Register a handset to another telephone base
Any analog cordless 1-line handset can register to any analog cordless 1-line telephone base. Any analog cordless 2-line handset
can register to any analog cordless 2-line telephone base.
When a registered cordless handset is idle, place it on another telephone base. This cordless handset automatically registers to the
new telephone base.
Handset battery charging
The battery must be fully charged before using the cordless handset for the rst time. The CHARGE LED turns on when the
cordless handset is charging on the telephone base or charging base. The battery is fully charged after 16 hours of continuous
charging. For best performance, keep the cordless handset in the telephone base or charging base when not in use.
1.
2.
3.
4.
1.
2.
3.
•
•
•
00
-
6
0
0H-0
8
7
W
E
:
D
I
C
C
F
0
0
7
0
0H
0
8
-
B
5
3
1
1
:
C
I
BY 1021
00
-
6
0
0H-0
8
7
W
E
:
D
I
C
C
F
0
0
7
0
0H
0
8
-
B
5
3
1
1
:
C
I
BY 1021
00
-
6
0
0H-0
8
7
W
E
:
D
I
C
C
F
0
0
7
0
0H
0
8
-
B
5
3
1
1
:
C
I
1 2 3 4
FCC ID
Screw
cover