UNIDEN CORDLESS TELEPHONES DECT1580 Series
Table of Contents Manual Conventions................................................ 17 Parts of the Handset................................................ 18 Parts of the Base..................................................... 19 Welcome........................................................................ 5 Accessibility............................................................... 5 Installing the Phone..................................................... 6 Choosing the Best Location..............
Customizing Your Handsets...................................... 29 Changing the Handset Banner................................. 29 Selecting a Ring Tone.............................................. 29 Activating AutoTalk................................................... 30 Activating Any Key Answer...................................... 30 Activating T-Coil Mode............................................. 37 Finding a Lost Handset..............................................
Activating the Base Call Screen............................... 46 Noise or Static on the Line....................................... 59 Installing a telephone line filter or DSL filter........ 60 Resetting the Handset............................................. 60 Resetting the Handset Without the Base................. 61 Changing the Line Mode for Multiple Extensions..... 62 Traveling Out of Range............................................ 62 Liquid Damage................................................
Welcome Note: Illustrations in this manual are used for explanation purposes. Some illustrations in this manual may differ from the actual unit. As an Energy Star® Partner, Uniden has determined that this product or product models meets the Energy Star® guidelines for energy efficiency. Energy Star® is a U.S. registered mark. Uniden is a registered trademark of Uniden America Corporation. Accessibility Uniden provides a customer service hotline for accessibility questions.
Installing the Phone Choosing the Best Location When choosing a location for your new phone, here are some important guidelines you should consider: PLACE YOUR BASE TRY TO AVOID Installing the Phone • Microwave ovens • Refrigerators Near an AC outlet and a telephone wall jack. • TVs • Other electronics In a centrally-located open area.
Installing the Battery Use only the Uniden BT-1015 rechargeable battery pack supplied with your cordless telephone. Unpack all handsets, battery packs, and battery covers. (If the battery cover is on the handset, press in on the notch and slide the cover off.) Line up the red and black wires on the battery pack connector with the sticker in the handset’s battery compartment. RED Push the battery pack connector in firmly. (You should hear it click into place.
Connecting the AC adapter To the base To avoid risk of fire and shock, only use the Uniden PS-0009 AC adapter with the base. Installing the Phone Connect the AC adapter to the DC IN 9V jack on the back of the base. Connect the AC adapter to a standard 120V AC wall outlet. Route the cord through the molded wiring channel. Don’t put any power cord where it people might trip over it or step on it. If a power cord becomes chafed or worn out, it can create a fire or electrical hazard.
Charging the Handset Place the handset in the base cradle with the display facing forward. Make sure that the charge LED illuminates when the handset is seated. What if the charge LED doesn’t light up? Reseat the handset; make sure the contacts on the bottom of the handset are lined up with the contacts in the charging cradle. Check the AC adapter connection. Make sure you are not using an outlet that’s controlled by a wall switch. Make sure that the charge LED illuminates when the handset is seated.
Connecting to the Phone Line Make sure that the battery pack is fully charged. Connect the telephone cord to the TEL LINE jack. Installing the Phone Connect the telephone cord to a telephone wall jack. What if Check TEL Line appears on the handset display? The telephone cord may not be connected correctly. Check the telephone cord connection.
Testing the Connection Pick up the handset from the cradle and press TALK/FLASH. You should hear a dial tone, and the display should show Talk. What if I can’t hear a dial tone? Check the telephone cord connection on the base. What if the display doesn’t show Talk? Make a quick test call, and then press END to hang up.
Changing the dial mode Installing the Phone Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most base networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you will need to change your phone’s dial mode.
Expanding Your Phone Adding accessory handsets Your phone supports a total of six cordless handsets, including any that were supplied with your phone. You can now place a fully-featured cordless handset anywhere AC power is available to connect the charging cradle. • Your phone is compatible with the following Uniden DECT6.0 accessory handsets: DCX150, DCX200, and DCX300. (Please visit our website at www.uniden.com for the most up-to-date list of compatible handsets.
3) On the handset, press and hold # until the handset beeps and displays Handset Registering. 4) When the handset has registered to the base, the LCD will display Registration complete then show the handset ID number. If the display shows Registration failed, repeat the process again. Note: If a handset has ever been registered to a base, reset the handset before you register it to a new base (see Resetting the Handset on page 60). Or to use multiple bases, see the next section.
4) Wait approximately thirty seconds. Registration complete will be displayed to indicate the handset has been registered to the base and a handset ID will be automatically assigned. The handset assigns its own ID to this base, too. (Since the base ID is based on the order in which the handset was registered to the different bases, a base may have different IDs on each handset.) If Registration failed appears in the LCD, please try these steps again.
Getting to Know Your New Phone Features • 1.9GHz DECT 6.
Terminology Used in this Manual Accessory Handsets Additional handsets that can register to the base, allowing you to add handsets without connecting another phone line. This base supports a total of six cordless handsets; see page 13 for compatible handsets. Base The main part of the phone that connects to your phone line and lets you make and receive calls. Charging cradle A cradle that comes with an accessory handset and charges the handset battery pack.
Parts of the Handset new message LED Earpiece Display (LCD) CLEAR/INT'COM key (clear/intercom) key (phonebook/left) TALK/FLASH key key (up) MENU/SELECT key key (caller ID/right) END key Speakerphone speaker and ringer key (down) key (speaker) Twelve-key dial pad Getting to Know Your New Phone /TONE key REDIAL/PAUSE key Microphone Battery compartment # key /MUTE key (messages/mute) Charging contacts 18
Parts of the Base Speaker key (delete) message counter LED FIND key key (skip) ANSWER ON/OFF key VOLUME key (volume up) VOLUME key (volume down) Charging contacts key (play/stop) key (repeat) charge LED Getting to Know Your New Phone 19
Using the Interface Using the Interface Reading the Display In standby During a call Time 6CNM 2 1(( # Handset ID and banner *CPFUGV 0GY %+& Number of new Caller ID calls received Call duration The ringer off icon indicates that the ringer is turned off. The voice mail icon appears when you have messages waiting in your voice mailbox. The privacy icon appears when the Privacy Mode is turned on. The speaker icon appears when the speaker phone is in use.
Your handset has a four-way function key that allows you to move the cursor on the display and access the most commonly used features at the touch of a button. • Press the left side of the key to open the phonebook. • Press the right side of the key to open the Caller ID list. • Press the top of the key to increase the ringer volume (while the phone is in standby) or speaker volume (while you are on a call).
Using the Interface Entering Text from Your Handset You can use the number keypad on your handset to enter text by referring to the letters printed on each number key. When you press the number key in a text entry field, the phone displays the first letter printed on the number key. Press the number key twice to display the second letter and three times to display the third. • When [Aa] appears on the display, capital letters are displayed first, then lower case letters, and then the number on the key.
Basic Setup Selecting a Language Setting the Day & Time To change the time shown in the display, follow the steps listed below. If you do not set the clock on your answering system, your messages on the answering system may not have the correct time and day stamp. 1) Press MENU/SELECT. ) Move the cursor to Day & Time and press MENU/SELECT. 3) Use and to select the day of the week, and press MENU/ SELECT. Note: The day of the week does not appear on the handset display.
Activating Personal Ring You can assign special ringer tones to anyone in your phonebook. When your phone gets a call, it looks up the Caller ID information in your phonebook. If you’ve assigned a personal ringer to that number, the phone uses it so you know who is calling. To turn the personal ringing on or off, follow these steps: 1) Press Menu/Select. 2GTUQPCN 4KPI ) Select the Handset Setup menu, and then the Personal Ring 1P submenu. 1HH 3) Move the cursor to select On or Off.
Setting Up the Phonebook Each handset has its own separate phonebook that holds up to seventy names and numbers. When a handset’s phonebook is full, the handset beeps and shows Memory Full on the display. You cannot add any names and numbers in that handset’s phonebook until you delete some of the existing ones. You can also use the phonebook entries to store a group of numbers (up to twenty digits) that you may need to enter once your call connects. This is referred to as chain dialing.
5) Assign a personal ring tone for this entry (PERSONAL RING). You can attach a special ring tone to each phonebook entry; the phone will use this ring tone when this person calls. Use and to select one of 2GTUQPCN 4KPI the seven different ring tone options (see Selecting a Ring Tone on page 29 0Q 5GNGEVKQP for a complete list of ring tones). As you scroll through the tones, you will (NKEMGT hear a sample of each tone (unless the handset ringer volume is set to off).
Storing Caller ID or Redial Numbers in the Phonebook You can store Caller ID records or redial numbers in the phonebook so you can use them later. Go to the Caller ID or redial list and select the number you want to store. (If the Caller ID information did not include the number, then you will not be able to store it.) 1) With the phone in standby, press to open the Caller ID list or Redial/Pause to open the redial list. ) Use and to scroll through the Caller ID records or redial numbers.
Deleting all Phonebook Entries 1) With the phone in standby, press . ) Press Menu/Select, and then select Delete All. Delete All? . appears in the display. 3) Move the cursor to select Yes. 4) Press Menu/Select. You will hear a confirmation tone, and Deleted! . appears in the display.
All of the following options are set separately for each handset, so you can customize a handset for each room in your house. Changing the Handset Banner Each handset will display a banner name once it is registered to the base. The default banner is Handset #1, Handset #2, etc. You can change the name your phone displays by changing the banner display. If you have more than one handset, the banner name identifies your handset. 1) Press Menu/Select.
Customizing Your Handsets Activating AutoTalk AutoTalk allows you to answer the phone simply by picking up the handset from the cradle. You do not have to press a button to answer the call. 1) Press Menu/Select. ) Select the Handset Setup menu, and then the AutoTalk submenu. 3) Move the cursor to select On or Off. 4) Press Menu/Select. You will hear a confirmation tone. Activating Any Key Answer Any Key Answer allows you to answer the phone by pressing any key on the twelve-key dial pad.
Using Your Phone From a cordless handset Making a call Hanging up Pick up the handset from the cradle. Press TALK/Flash. Listen for the dial tone. Dial the number. 1) ) 3) 4) OR 1) ) 3) Pick up the handset from the cradle. Dial the number. Press TALK/Flash. 1) Pick up the handset. (If AutoTalk is on, the phone will answer when you pick up the handset from the cradle.) ) Press TALK/Flash. (If Any Key Answer is on, you can also press any key on the dial pad.
Making a Call from the Phonebook 1) With the phone in standby, press to open the phonebook. ) Find the phonebook entry you want to call (see Finding a Phonebook Entry on page 26). 3) Press TALK/Flash or to dial the number. Note: You can also press TALK/Flash or dial, and then press Menu/Select. before you open the phonebook.
Using Caller ID, Call Waiting, and Redial Lists If you subscribe to Caller ID service from your phone company, your phone will show you the caller’s phone number and name (if available) whenever a call comes in. If you subscribe to Caller ID on Call Waiting, the phone will also show you the name and the number of any call that comes in while you’re on the line. Using the Caller ID List You can store up to thirty Caller ID numbers in each handset. Caller ID records are stored from newest to oldest.
Seven-digit dialing Using Caller ID, Call Waiting, and Redial Lists If you can make a local call by dialing only seven digits instead of ten, you can tell the phone to hide your local area code in the Caller ID list; any calls from outside your area code will show all ten digits. This setting applies to the base and all handsets currently connected to the same base. To program your local area code: 1) Press Menu/Select. ) Select the Global Setup menu, and then the Area Code submenu.
Using Call Waiting If you have Call Waiting service and a second call comes in when you are on the phone, a call waiting tone will sound. Press TALK/Flash to accept the waiting call. There is a short pause, and then you will hear the new caller. To return to the original caller, press TALK/Flash. Note: You must subscribe to Call Waiting service for this feature to operate. Not all features are available in all areas.
Adjusting the Ringer, Earpiece and Speaker Volume Adjusting the Ringer, Earpiece and Speaker Volume Adjusting the Ringer Volume You can choose from four ringer volume settings (off, low, medium, and high) separately on each handset or the base. 1) With the phone in standby, press or on the handset or VOLUME or VOLUME on the base. The handset or base sounds the ringer at that level. ) Use on the handset or VOLUME on the base to make the ringer volume louder.
Adjusting the Audio Tone If you aren’t satisfied with the audio quality of your phone, you can adjust the Audio Tone of the earpiece while on a call. Your phone gives you three audio tone options: low, natural and high; the default setting, Natural Tone, is recommended for hearing aid users. Audio tone adjustments only apply to the earpiece, not the speakerphone. To adjust the audio tone: 1) While on a call, press Menu/Select. ) Move the cursor to select Audio Tone, and then press Menu/Select.
Finding a Lost Handset To locate a misplaced handset, press find on the base when the phone is in standby. The handsets connected to the paging base will beep for one minute, and PAGING appears on the handset display. To cancel paging, press find again or any key on the found handset. Note: Handsets that are not currently connected to this base will not be paged.
Transferring a Call You can transfer a call from one handset to another. The handsets must be currently connected to the same base (see page 15). 1) During a call, press Clear/Int’com. or to select the handset you want to transfer the call to, and then press Menu/Select. Select All ) Use to page all other handsets. The call will automatically be placed on hold, and a paging tone sounds. To cancel the transfer, press TALK/Flash or .
Using Special Features Privacy Mode Privacy mode prevents other handsets (that are connected to the same base) from interrupting your call. As long as your handset is in privacy mode, other handsets can’t join your call or make any calls of their own: their displays will show Unavailable. 1) While on a call, press Menu/Select. ) Select Call Privacy. Privacy Mode On appears in the display for two seconds; appears and remains in the display until the feature is turned off.
Answering an intercom page When the intercom page tone sounds, the display will show the ID of the handset that is paging. 1) Press TALK/Flash or Clear/Int’com. Note: If AutoTalk is on, the handset will automatically answer the page when you pick up the handset from the cradle. If Any Key Answer is on, you can also press any key on the handset’s dial pad. ) To hang up an intercom call, press END. Muting the Microphone Mute turns off the microphone so the caller can’t hear you.
Using a Voice Mail Service If you subscribe to a voice mail service, you can use your phone to access your voice mailbox. When there are messages waiting in your voice mailbox, the new message LED on the handset flashes, and appears in the handset display. Note: This notification feature supports the voice mail service that uses Frequency Shift Keying (FSK) for the message notification signal only.
You can set up your answering system’s features from the handset. Only one handset at a time can access the answering system menus. Note: If you have multiple bases, select the base with answering system you want to access (see page 15). Recording a Personal Greeting Your answering system comes with a pre-recorded outgoing message or greeting that plays when you receive a call: “Hello, no one is available to take your call. Please leave a message after the tone.
Setting Up the Answering System Do nothing.. 4) To keep this greeting: To switch to the other greeting: Press 6 while the system is playing the current greeting. 5) Each time you press 6, the system switches between the pre-recorded and the personal greeting. The last greeting you hear is used as the current greeting. Deleting Your Personal Greeting You can delete your personal greeting from the base. You cannot delete the pre-recorded greeting. 1) Press /mute.
The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you enable the Toll Saver (TS) setting, the answering system picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance call to check your messages, you can hang up after the third ring to avoid long distance billing charges.
Setting Up the Answering System Activating the Message Alert The message alert feature sounds a short alert tone every fifteen seconds whenever you have a new message. To turn on the message alert: 1) Press Menu/Select. ) Select the Ans. Setup menu, and then the Message Alert submenu. 3) Move the cursor to select On or Off. 4) Press Menu/Select. You will hear a confirmation tone.
Using the Answering System Turning Your Answering System On and Off From the base From the handset 1) Press Menu/Select. ) Select the Ans. Setup menu, and then the Ans. On/Off submenu. 3) Move the cursor to select On. 4) Press Menu/Select. You will hear a confirmation tone. Turning Off 1) With the phone in standby, press . ANSWER ON/OFF. ) The phone announces “Answering System is off.” 3) The message counter LED is no longer illuminated. 1) Press Menu/Select. ) Select the Ans.
Remote Operation from the Handset You can operate your answering system from the handset whenever the phone is in standby. • Press /mute to start remote operation. • During remote operation, the phone beeps to let you know it’s waiting for your next command. Using the Answering System • Press the number listed next to the commands. (see the table for a list of all available commands).
Reviewing Messages The message counter LED on the base displays the number of messages stored in memory. When you have new messages (that you have not listened to yet), the message counter LED on the base and the new message LED on the handset flash. The answering system plays your new messages first. If you have no new messages, the system plays your old messages. You can review your messages from the base or from the handset: From the base From the handset Press /mute.
Screening Calls From the base From the handset Using the Answering System • While the system is taking the message, simply listen to the caller over the base speaker. (You need to activate the base call screen feature in advance. See page 46.) • To mute the call screen and allow the caller to continue leaving the message, press . • While the systems is recording the message, press . /mute. If another handset is screening a call, you will hear a beep and you will not be able to screen the call.
To operate from a remote location, use any touch-tone telephone, and follow these steps: 1) Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about ten rings and sounds a series of beeps. ) During the greeting or the beeps (if answering system is off), press 0 and enter your security code/PIN within two seconds. 3) The answering system announces the current time and the number of messages stored in memory..
Wall Mounting the Base This phone can be mounted on any standard telephone wall plate using an optional wall-mount bracket. You can purchase a wall-mount bracket by calling the Uniden Parts Department. (See the back cover page for contact information.) Route the telephone cord through the hole of the wall-mount bracket. Connect the AC adapter and the telephone cords as shown on pages 8 and 10.
Place the mounting slots over the pins on the wall plate. Slide the base down to lock it into place. Wall plate (To AC outlet) At the bottom of the base, pinch the two "nose" of the wall-mount bracket as shown, and then slide the bracket away from the base. 53 Wall Mounting the Base Note: Mounting the phone directly on the wall • Be sure the wall is capable of supporting the weight of the phone, and use the proper type of anchoring device for the wall material.
Maintenance Maintenance Specifications Operating temperature AC adapter Battery pack 32° F to 122° F (0° C to 50° C) Base Part number PS-0009 Input voltage 120V AC, 60 Hz Output voltage 9V DC @ 350mA Part number BT-1015 Capacity 650mAh, 2.4V DC Charging cradle PS-0007 120V AC, 60 Hz 9V DC @ 210mA Notes: • Use only the supplied AC adapters. • Be sure to use the proper adapter for the base and any chargers.
When the battery pack is very low, the phone is programmed to eliminate functions in order to save power. When Low Battery - Charge Handset appears in the handset display and the phone is in standby, none of the keys will operate. If you are on a call, complete your conversation as quickly as possible, and return the handset to the cradle. The battery pack needs to be charged when the empty battery icon appears.
Troubleshooting Common Issues If your phone is not performing to your expectations, please try these simple steps first. If these steps do not solve your problem, please call our Customer Hotline (see the back cover for contact information). Troubleshooting When you have this problem... Try... The charge LED won’t illuminate when the handset is placed in the cradle. • Checking the AC adapter connection (see page 8). • Re-seating the handset in the cradle.
When you have this problem... Try... • Moving the handset closer to the base. • Seeing if another handset has Privacy Mode turned on (see page 40). • Making sure the base is plugged in (see page 8). The phone keeps ringing when I answer on an extension. • You may have to change the line mode. Contact customer service for more information (see page 62). No handsets will display any Caller ID information. • Checking to see if the call was placed through a switchboard.
Troubleshooting When you have this problem... Try... I can’t get two handsets to talk to an outside caller. • Checking to see that there are not two handsets already using the conference feature (see page 38). • Making sure another handset is not in Privacy Mode (see page 40). • Making sure both handsets are registered to and currently connected to the same base (see pages 14 and 15). The answering system does not work. • Checking the AC adapter connection (see page 8).
Weak or Hard to Hear Audio If the caller’s voice sounds weak or soft, the signal might be blocked by large metal objects or walls; you might also be too far from the base, or the handset’s battery may be weak. • Try adjusting the volume of the earpiece (see page 36) or the audio tone (see page 37). • Try moving around while you’re on a call or moving closer to the base to see if the sound gets louder. • Make sure the handset’s battery is fully charged.
Installing a telephone line filter or DSL filter Troubleshooting Any broadband Internet service that uses your telephone. line might interfere with standard phones. The most common type of these services, DSL, often causes static on your telephone. Fortunately, an easy-to-install filter removes this static from the line. Technicians who install DSL service usually leave several filters for the customers; if you can’t find them, call your DSL provider or look in any electronics store.
5) When the base information is deleted, the handset displays Handset not registered-place handset on base to register. See your Owner’s Manual for help. 6) Re-register the handset to the base (see Registering accessory handsets on page 13). If the handset cannot contact the base, it will display Out Of Range. Make sure the handset is in range of the base and the base is connected to power; you can also reset the handset without the base (see the next section).
Troubleshooting Changing the Line Mode for Multiple Extensions Line mode refers to the method that telephones use to signal each other that an extension is in use. Customer service may recommend changing the line mode if you have any of the following problems: • Your phone keeps ringing after someone answers on an extension phone. • Your answering system doesn’t stop recording when you answer on an extension phone. • Caller ID displays briefly and then clears.
Liquid Damage Moisture and liquid can damage your cordless phone. • If the handset or base is exposed to moisture or liquid, but only the exterior plastic housing is affected, wipe off the liquid, and use as normal. • If moisture or liquid has entered the plastic housing (i.e. liquid can be heard in the phone or liquid has entered the handset battery compartment or vent openings on the base), follow the steps below.
Precautions! Rechargeable Nickel-Cadmium Batteries Must Be Recycled or Disposed of Properly Before you read anything else, please observe the following: Warning! • Uniden voluntarily participates in an RBRC® industry program to collect and recycle nickel-cadmium batteries at the end of their useful life, when taken out of service within the United States.
Important Safety Instructions The FCC Wants You To Know When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. . Avoid using a telephone (other than a cordless type) during an electrical storm.
To insure the safety of users, the FCC has established criteria for the amount of radio frequency energy various products may produce depending on their intended usage. This product has been tested and found to comply with the FCC’s exposure criteria. For body worn operation, the FCC RF exposure guidelines were also met when used with the Uniden accessories supplied or designed for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines and should be avoided.
I.C. Notice --Connect the equipment into an outlet on a circuit different from . that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Terminal equipment Radio interference NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number.
One Year Limited Warranty One Year Limited Warranty A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. Important: Evidence of original purchase is required for warranty service.
Index A B Banner.......................................... 29 Base Installing...................................... 8 Multiple bases........................... 14 Parts of the base....................... 19 Wall mounting........................... 52 Battery Battery life................................. 54 Installing...................................... 7 Low battery alert....................... 55 Replacement and handling....... 55 Caller ID.......................................
M Maintenance................................. 54 Making calls.................................. 31 Using Caller ID.......................... 33 Using redial............................... 35 Using the phonebook................ 32 Message alert......................... 46, 50 Multiple bases.............................. 14 Mute Microphone............................... 41 Ringer....................................... 36 R O Redial Deleting a record....................... 35 Making a calls with...........
Remote Operation Card CUT CUT REMOTE OPERATION CARD REMOTE OPERATION CARD Remote access away from home Remote access away from home Turn on the answering system remotely 1. Call your phone and let it ring 10 times until you hear a beep. 2. Press 0 and then enter your PIN code. 3. Press 0 then 5 to stop the announcement. 4. Press 0 then 6 to turn the answering system on. 1. Call your phone number from a touch-tone phone. 2. During the outgoing message, press 0 and enter your PIN code.
CUT Task CUT Key Task Key Repeat a Message Repeat a Message Play Incoming Messages Play Incoming Messages Skip a Message Skip a Message Delete a Message Delete a Message Stop Operation Stop Operation Answering System On Answering System On Answering System Off Answering System Off Help Help CUT Task CUT Key Task Repeat a Message Repeat a Message Play Incoming Messages Play Incoming Messages Skip a Message Skip a Message Delete a Message Delete a Message Stop Operation Stop
Memo 73
Memo 74
Memo 75
VISIT OUR WEBSITE AT WWW.UNIDEN.COM IF YOU... • ...HAVE A QUESTION OR A PROBLEM. Or call our Customer Hotline at 1-800-297-1023 during regular business hours.* • ...ARE LOOKING FOR A PART OR ACCESSORY. Or call our Parts Department at 1-800-554-3988 during regular business hours.* • ...NEED SPECIAL ASSISTANCE DUE TO A DISABILITY. Or call our Accessibility help line at 1-800-874-9314 (voice or TTY). © 2008 Uniden America Corp., Fort Worth, Texas. Printed In China.
