SIP Contemporary Series D R AF T CTM-S2115 SIP 1-Line Hidden Base with Cordless Handset and Charger Quick Start Guide
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. This product should be installed by a qualified technician. 2. This product should only be connected to the host equipment and never directly to the network such as Public Switch Telephone Network (PSTN) or Plain Old Telephone Services (POTS). 3. Read and understand all instructions. 4.
14. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: • When the power supply cord or plug is damaged or frayed. • If liquid has been spilled onto the product. • If the product has been exposed to rain or water. • If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions.
place. Refer to the full instructions in Installation in the user’s manual. 21. Listed PoE (The product is considered not likely to require connection to an Ethernet network with outside plant routing). CAUTIONS • Keep small metallic objects such as pins and staples away from the handset receiver. • There may be a risk of explosion if a wrong type of handset battery is used (CTM-S2115). Use only the supplied rechargeable battery (BT164392/BT264392) or replacement battery (BT264392).
9. Ce produit ne doit être utilisé qu’avec le type de source d’énergie indiqué sur l’étiquette de marquage. Si vous n’êtes pas sûr du type d’alimentation électrique sur place, consultez votre revendeur ou votre compagnie d’électricité locale. 10. Ne laissez rien reposer sur le cordon d’alimentation. N’installez pas ce produit à un endroit où l’on pourrait marcher sur le cordon. 11.
un environnement contenant des concentrations de gaz inflammables ou propices aux flammes, à moins qu’il n’y ait une ventilation adéquate. Une étincelle dans un tel environnement pourrait créer un incendie ou une explosion. Ces environnements peuvent comprendre : l’utilisation médicale de l’oxygène sans ventilation adéquate; les gaz industriels (solvants de nettoyage; vapeurs d’essence; etc.); une fuite de gaz naturel; etc. 17.
using ousing Your package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.
S211X BASE Artwork S211X BASE Artwork Base Station Layout 4 1 5 2 RESET T 6 3 AF 7 1 R 8 FIND HANDSET button. Short press (for less than 2 seconds) to find the handset by making it ring. Short press again to stop handset ringing. D • • Short press (for less than 2 seconds) ten times, then long press (between 5 and 10 seconds) to restore the phone’s factory defaults. POWER LED VoIP LED Antenna AC adapter input Reset button. Short press (for less than 2 seconds) to reboot the phone.
Cordless Handset Layout 6 6 7 7 1 8 8 2 2 9 9 3 3 4 5 10 10 11 11 12 12 13 13 D R 4 5 AF T 1 1 2 3 4 5 6 FLASH/TALK OFF Numeric dial keys 7 8 9 10 SPEAKER key Speed dial keys Programmable key #1 Programmable key #2 Handset earpiece 11 12 13 14 15 9 VOLUME +/EMERGENCY HOLD MUTE MESSAGES Low battery LED Microphone Speaker MESSAGE WAITING LED 14 14 15 15
AF T Cordless Handset Charger Layout Charging poles CHARGE LED D R 1 2 10
Base Station Installation This section assumes that your network infrastructure is established and that your IP PBX phone service has been ordered and configured for your location. For more information about IP PBX configuration, please refer to the SIP Phone Configuration Guide. You can power the base station using a compatible VTech power adapter (sold separately) or using Power over Ethernet (PoE Class 2) from your network.
To mount the base station on a wall: AF T 1. Install two mounting screws on the wall. Choose screws with heads larger than 5 mm (3/16 inch) in diameter (1 cm / 3/8 inch diameter maximum). The screw centers should be 5 cm (1 15/16 inches) apart vertically or horizontally. 2. Tighten screws until only 3 mm (1/8 inch) of the screws are exposed. 3. Attach the mounting plate to the top of the base station.
R AF T 5. Place the base station over the mounting screws. D 6. Connect the Ethernet cable and power as described on page 11.
Handset Charger Installation 1. Install the handset charger as shown below. AF T • Make sure the supplied power adapter is securely plugged into an outlet not controlled by a wall switch. D R 2. Bend a small paperclip and gently insert it in the handset battery ON pinhole to turn on the cordless handset. • Without turning on the battery, the handset cannot be charged or operated. • The battery is fully charged after 16 hours of continuous charging.
CAUTIONS Use only the supplied power adapter. The supplied power adapter is not designed for use in any other devices. Misuse of it on your other devices shall be prohibited. To order a replacement, call 1-888-907-2007.
Finding your phone’s IP address If you want to use the Web User Interface to configure the phone, you need to know the phone’s IP address. You can obtain the phone’s IP address using either of the following methods: * Voice Menu 1. When the phone is idle, press this key sequence on the handset: TALK A digitized voice on the handset will announce Voice Menu options. 2. Press 1 for network configuration. 3. Press 2 for IP address. T A digitized voice on the handset will announce the IP address.
AF T 4. Under Select target models, select the CTM-S2115 checkbox. R 5. Enter your Password, and then click Apply. The default password is admin. The Admin tool begins scanning IP addresses. As the scan proceeds, the list of devices is updated. D 6. Look for your phone’s MAC Address. The table entry will display the phone’s IP address. Check the MAC Address against the LAN MAC or the WIFI MAC, depending on which connection (LAN or WIFI) is in use.
Voice Menu The Voice menu enables you to use the handset to query and change phone settings. To access the Voice Menu: 1. When the phone is idle, press this key sequence on the handset: TALK Û Û Û Û . A digitized voice on the handset will announce Voice Menu options. 2. Press the number key on the handset to select the desired menu option, or enter information. A list of menu options is shown in the diagram below.
Handset Battery Charging The battery must be fully charged before using the cordless handset for the first time. The CHARGE LED turns on when the handset is charging on the telephone base, charging base or charging stand. The battery is fully charged after 16 hours of continuous charging. For best performance, keep the cordless handset in the telephone base, charging base or charging stand when not in use. Replacing a Cordless Handset Battery The cordless handset battery is preinstalled.
T U A H E L S R AF T P U E /C V E ) É T H Ô . i-M C S . N IE S h R E A E IL 0m TT P : A S s 40 : le V NT B LE E pi .4 E RE R ID E e c- (2 M S lo 2 SE CTU RC in IS / B 34 S N E ch H k 83 TI PU U P en T R ac P BT2 VE OR R O ué iq ry 2/ / A N E te 34 G R R br at 83 IN U INÉ / Fa B B C T1 N B AR OT IN na hi W N S C O D PA in E e N ad M 15 R C 35 THIS SIDE UP 4.
Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that: Pacemaker patients Should keep wireless telephones at least six inches from the pacemaker.
Electrical power: The telephone base of the cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged, switched off or if the electrical power is interrupted. Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs.
FCC, ACTA and IC regulations FCC Part 15 T This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation.
instructions in the user’s manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your telephone service provider.
This product can only be connected to the host equipment and never directly to the network. Industry Canada This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to be connected to a telephone interface.
La confidentialité des communications peut ne pas être garantie lors de l’utilisation de ce téléphone. L’appareil de l’unité de base est conforme aux directives d’exposition aux RF. Après examen de ce matériel aux conformité ou aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité d’acquérir les informations correspondantes. La distance minimale du corps à utiliser le dispositif est de 20cm.
Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road., Suite 555, Tigard, OR 97223, United States Phone: 1 (888) 907-2007 Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND/OR TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the unplugged cords.
T AF R D Specifications are subject to change without notice. Copyright © 2021 VTech Telecommunications, Inc. All Rights Reserved.
