Multiple handset use Push-to-talk (PTT) Change a one-to-one PTT call to an intercom call You can convert a one-to-one PTT session to an intercom call. 1. When your device shows Press and hold [PTT] to talk, press INTCOM. The screen shows Switch to Intercom? 2. Press SELECT. Your device displays Calling BASE 0 or Calling HANDSET X. The destination device briefly shows Push to talk Ended and then HANDSET X is calling or BASE 0 is calling. The destination device rings. 3.
Multiple handset use Push-to-talk (PTT) Make an outgoing call during PTT call • During a one-to-one PTT call, press PHONE/FLASH on your handset or /SPEAKER on your telephone base to get a dial tone. The PTT call ends automatically. • During a one-to-group PTT call, press PHONE/FLASH on the initiating handset or /SPEAKER on the initiating telephone base. The PTT call ends automatically and you get a dial tone.
Directory About the directory Shared directory The directory is shared by all handsets and the telephone base. Changes made to the directory from any device apply to all. NOTE: Only one handset or the telephone base can review the directory at a time. If another device tries to enter the directory, the screen shows Not available at this time. Capacity The directory can store up to 50 entries, with a maximum of 15 alphanumeric characters (including spaces) for names and 30 digits for telephone numbers.
Directory Create directory entries Create a new directory entry 1. Press MENU/SELECT in idle mode to enter the main menu. 2. Press qCID or pDIR to scroll to Directory, then press MENU/SELECT. 3. Press qCID or pDIR to highlight Add contact. 4. Press MENU/SELECT. 5. Use the dialing keys to enter a telephone number (up to 30 digits) when prompted. • Press qCID or pDIR to move the cursor to the left or right. • Press MUTE/DELETE on the handset or X/DELETE on the telephone base to erase a digit.
Directory Create directory entries NOTE: The first letter of every word is a capital letter. The remaining letters in a word start as lower case letters as shown in the chart below. Characters by number of key presses Dialing keys 1 2 3 4 5 6 7 8 9 10 11 1 1 .
Directory Review the directory Review directory entries 1. Press pDIR when in idle mode. The summary screen shows briefly and then the first entry in the directory shows. -ORPress MENU/SELECT when in idle mode, then press qCID or pDIR to scroll to Directory. Press MENU/SELECT twice. 2. Press qCID or pDIR to browse through the directory. Entries appear alphabetically by the first letter in the name.
Directory Search the directory Search by name 1. Press pDIR in idle mode to show the first listing in the directory. 2. When an entry appears, press the dialing keys (0-9) to start a name search. The directory shows the first name beginning with the first letter associated with the dialing key if there is an entry in the directory beginning with that letter. Press qCID or pDIR to scroll through the directory. 3. To see other names starting with the letters on the same dialing key, keep pressing the key.
Directory Dial, delete or edit directory entries To dial, delete or edit a directory entry (name and number), the entry must be displayed on the screen. Use Review the directory (page 66) or Search by name (page 67) to show an entry. Display dial To dial a displayed number from the directory, press PHONE/FLASH or /�������� SPEAKER on the handset, or /������� SPEAKER on the telephone base. Delete a directory entry Using a cordless handset: To delete the displayed directory entry, press SELECT to confirm.
Directory Dial, delete or edit directory entries Edit a directory entry 1. When a directory entry displays, press MENU/SELECT. The screen shows EDIT NUMBER along with the phone number to be edited. If you only want to edit the name, skip to Step 3. 2. To edit the number: • Press the dialing keys to add digits. • Press qCID or pDIR to move the cursor to the left or right. • Press MUTE/DELETE on the handset or X/DELETE on the telephone base to erase a digit.
Directory Speed dial The telephone system has nine speed dial locations (2-9, 0) and a voicemail access location 1 where you can store the telephone numbers you wish to dial more quickly. You can store up to 30 digits in each location. Speed dial assignments can only be selected from the existing directory entries. The voicemail access number must be manually entered. In the directory, speed dial locations are indicated by their number on the bottom right hand corner of the entry.
Directory Speed dial Assign your voicemail speed dial number To assign your voicemail speed dial number to location 1, see page 24 or page 29. The voicemail speed dial entry does not show in the bottom right corner. Reassign a speed dial number 1. When the telephone is idle, press MENU/SELECT. 2. Press qCID or pDIR to scroll to Directory. Press MENU/SELECT. 3. Press qCID or pDIR to scroll to Speed dial. Press MENU/SELECT. 4.
Directory Speed dial Delete a speed dial number 1. When the telephone is idle, press MENU/SELECT. 2. Press qCID or pDIR to scroll to Directory. Press MENU/SELECT. 3. Press qCID or pDIR to scroll to Speed dial. Press MENU/SELECT. 4. Press qCID or pDIR to scroll to the location you wish to delete the speed dial number from, then: • Press MUTE/DELETE on the handset or X/DELETE on the telephone base to delete the displayed speed dial number.
Caller ID About caller ID This product supports caller ID services offered by most telephone service providers. Caller ID allows you to see the name, number, date and time of calls. The available caller ID information will appear after the first or second ring. Information about caller ID with call waiting Caller ID with call waiting lets you see the name and telephone number of the caller before answering the call, even while on another call.
Caller ID Caller ID history How the caller ID history (caller ID log) works The telephone stores caller ID information about the last 50 incoming calls in the telephone base. Entries are stored in reverse chronological order. The phone deletes the oldest entry when the log is full to make room for new calls. This information is common to the telephone base and all handsets, so changes made using any handset or the telephone base are reflected in all other devices.
Caller ID Caller ID operation Memory match If the incoming telephone number matches the last 7 digits of a telephone number in your directory, the name that appears on the screen matches the corresponding name in your directory. For example, if Christine Smith calls, her name appears as Chris if this is how you entered it into your directory. NOTE: The number shown in the caller ID log will be in the format sent by the telephone service provider.
Caller ID Caller ID operation Review the caller ID history Review the caller ID history to find out who called, to return the call, or to copy the caller’s name and number into your directory. Caller ID log empty appears if there are no records in the caller ID log. 1. When the handset or the telephone base is in idle mode, press qCID 10/15 to review the caller ID history in reverse chronological order starting with the most recent call. -ORReview the caller ID history by pressing MENU/SELECT.
Caller ID Caller ID operation View dialing options Although the incoming caller ID log entries have ten digits (the area code plus the seven-digit number), in some areas, you may need to dial only the 7 digits, 1 plus the seven digits, or 1 plus the area code plus the seven digits. You can change and store the number of digits that you dial in the caller ID log.
Caller ID Caller ID operation Save a caller ID log entry to the directory 1. When in the caller ID log, press qCID or pDIR to browse. 2. Press MENU/SELECT to select an entry. 3. When the screen displays EDIT NUMBER, use the dialing keys to edit the number. • Press qCID or pDIR to move the cursor to the left or right. • Press MUTE/DELETE on the handset or X/DELETE on the telephone base to backspace and erase a digit.
Caller ID Reasons for missing caller ID information There are occasions when other information or no information shows for various reasons: On-screen message Reason PRIVATE NUMBER The caller prefers not to show the phone number. PRIVATE NAME The caller prefers not to show the name. PRIVATE CALLER The caller prefers not to show the phone number and name. UNKNOWN NUMBER Your telephone service provider cannot determine the caller’s number.
Answering system Answering system settings Use the answering system menu of a system handset or the telephone base to set up the announcement message, turn on or off the answering system or message alert tone, activate call screening, or change the number of rings, remote access code or message recording time. If you turn off the answering system and you change any setting in the answering system setup menu, the answering machine automatically turns on again. 1.
Answering system Answering system settings To record a new outgoing announcement: Using a cordless handset: 1. When the handset is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys, then press MENU/SELECT. 3. Press MENU/SELECT again to select Announcement. 4. Press MENU/SELECT to select Record annc. The system announces, “Record after the tone. Press 5 when you are done.” 5. Speak towards the handset to record your announcement.
Answering system Answering system settings To delete or reset your outgoing announcement: Using a cordless handset: 1. When the handset is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys, then press MENU/SELECT. 3. Press MENU/SELECT again to select Announcement. 4. Press qCID or pDIR to scroll to Play annc, then press MENU/SELECT. 5. While the announcement is playing, press MUTE/DELETE to delete the announcement.
Answering system Answering system settings Answer on/off Unless you change it, the answering system is on and ready to record messages. You can turn the answering system off, but if you do so, the answering system does not answer calls and record incoming messages. To turn the answering system on or off: Using a cordless handset: 1. When the handset is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys, then press MENU/SELECT. 3.
Answering system Answering system settings Call screening Use this feature to choose whether incoming messages can be heard over the speaker when they are being recorded. If you turn call screening on, you hear the incoming message. While monitoring an incoming message, you can answer the call by pressing PHONE/FLASH on the handset, or /�������� SPEAKER on the telephone base. To change the setting: Using a cordless handset or the telephone base: 1.
Answering system Answering system settings Number of rings You can set the answering system to answer an incoming call after two, three, four, five or six rings. You can also select toll saver. If toll saver is selected, the answering system answers a call after two rings when you have new messages, and after four rings when there are no new messages. This feature allows you to check for new messages and avoid paying long distance charges when calling from out of your local area.
Answering system Answering system settings Remote access code To access your answering system remotely from any touch-tone phone, you need to enter a two-digit number (00-99). By default, the remote access code is 19. To change the remote access code: Using a cordless handset or the telephone base: 1. When the handset or telephone base is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys, then press MENU/SELECT. 3.
Answering system Answering system settings Message alert tone When the message alert tone is set to On, and there is at least one new message, the telephone base beeps every ten seconds. Unless you change it, the message alert tone is set to off. There is no audible alert at the handset. To change the setting: Using a cordless handset or the telephone base: 1. When the handset or telephone base is in idle mode, press MENU/SELECT to enter the main menu. 2.
Answering system Answering system settings Message recording time You can set the recording time allowed for incoming messages. The message length is three minutes by default. To change the setting: Using a cordless handset or the telephone base: 1. When the handset or telephone base is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys, then press MENU/SELECT. 3. Press qCID or pDIR to scroll to Ans sys setup, then press MENU/SELECT. 4.
Answering system About the answering system Answering system and voicemail indicators Your telephone has separate indicators for two different types of voice messages: those left on its built-in digital answering system and those left at your telephone service provider’s voicemail (fees may apply). Your telephone’s built-in digital answering system messages and voicemail messages are separate. Each alerts you to new messages differently.
Answering system About the answering system Using the answering machine and voicemail together You can also use your telephone answering system and voicemail together by setting your built-in answering system to answer before voicemail answers as described below. To learn how to program your voicemail settings, contact your telephone service provider. If you are on a call, or the answering system is busy recording a message and you receive another call, the second caller can leave a voicemail message.
Answering system About the answering system Voice prompts The system provides voice prompts to guide you through the setup procedures at the telephone base, message playback, remote access and recording outgoing announcements. Call screening To screen a call at the telephone base: If the answering system and call screening are on (see Call screening on page 84), the announcement and the incoming message broadcast at the telephone base when a call is answered by the answering system.
Answering system About the answering system Call intercept While screening a call, you can stop recording and speak to the caller by pressing PHONE/FLASH on the handset or /������� SPEAKER on the telephone base. Base ringer Press q/VOLUME/p on the telephone base to adjust the ringer volume when the telephone is not in use. You hear a sample of the ringer while adjusting the volume. The telephone base shows Ringer off when you set the volume to 0.
Answering system Message playback If you have new messages, you hear only the new messages in chronological order. If there are no new messages, the system plays back all the messages (in chronological order). If there are both new and old messages, you have the option of playing the new or old messages. When playback begins, the total number of messages is announced. Before each message, you hear the day and time of the recording.
Answering system Message playback To listen to messages on a cordless handset: 1. When the handset is in idle mode, press MENU/SELECT to enter the main menu. 2. Press MENU/SELECT again to select Play messages. • If there are new and old messages, press qCID or pDIR to select Play new msgs or Play old msgs, then press MENU/SELECT. • If there are only new or only old messages, they will play automatically. The system announces the number of messages, then begins playback.
Answering system Message playback When messages are playing on the handset: • Press qCID/VOLUME or pDIR/VOLUME to adjust the message playback volume. • Press EQ to adjust the message playback audio quality. • Press 6 to skip to the next message. • Press 4 to repeat the message. Press twice to hear the previous message. • Press MUTE/DELETE to delete the message. • Press 5 or OFF/CANCEL to stop the playback. • Press /������� SPEAKER to switch between speakerphone mode and handset mode.
Answering system Message playback Delete all old messages You can only delete old (reviewed) messages. You cannot delete new messages until you review them. You cannot retrieve deleted messages. To delete all old messages on the telephone base: 1. When the telephone is idle, press X/DELETE. The system announces, “To delete all old messages, press DELETE again.” 2. Press X/DELETE again. The system announces, “All old messages deleted.” -OR1. Press MENU/SELECT when in idle mode to enter the main menu. 2.
Answering system Recording and playing memos Memos are your own recorded messages used as reminders for yourself or others using the same answering system. You can record your own memos using a system handset or the telephone base. Play and delete them in the same way as incoming messages. Record a memo Using a cordless handset: 1. When the handset is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys. Press MENU/SELECT. 3.
Answering system Recording and playing memos Using the telephone base: 1. When the telephone base is in idle mode, press MENU/SELECT to enter the main menu. 2. Press qCID or pDIR to scroll to Answering sys. Press MENU/SELECT. 3. Press qCID or pDIR to highlight Record memo, then press MENU/SELECT. The system announces, “Record after the tone. Press 5 when you are done.” You can record a memo for up to four minutes. 4. Speak towards the telephone base to record a memo. 5. Press 5 to stop recording.
Answering system Base message counter displays The base message counter shows the total number of answering system messages. See the table below for other message counter displays. Message counter displays 0 1-99 -- No messages. Total number of messages and memos. The system is answering a call, or someone is trying to reach it remotely. The system is in program mode.
Answering system Remote access You can reach your answering system remotely by dialing your home telephone number from any touch-tone telephone. To remotely reach your answering system: 1. Dial your telephone number from any touch-tone telephone. 2. When the system answers, enter the two-digit remote access code (19 is the default code. See page 86 to change it). • The system automatically announces the number of new or old messages (if any), and then begins to play them. 3.
Answering system Remote access Cut out and carry the remote access wallet card at the back of this user’s manual for quick reference. NOTES: • If you do not enter a valid remote access code, the system answers the call automatically. • If you pause for more than four seconds during remote access, you hear a help menu listing all features and commands. If there is no command for another 20 seconds, the call ends automatically.
Appendix Adding and registering handsets/headsets Your telephone can support up to 12 DECT 6.0 cordless handsets (AT&T model CL80113, sold separately) or up to ten cordless handsets and two cordless headsets (sold separately). Visit www.telephones.att.com/headsets for a list of compatible DECT 6.0 cordless headsets. Each new handset or headset must be registered to the telephone base before use. You must register each handset or headset separately.
Appendix Adding and registering handsets/headsets If registration fails, the system will automatically try to register again. If registration fails after the third try, Registration failed appears on both screens. The handset shows To register HS, see manual and the telephone base returns to idle mode. This may take up to five minutes to occur. Please start again from Step 1. NOTES: • You cannot register a handset if any other system handset is in use.
Appendix Deregistering handsets You may need to deregister your handsets if: • You have 12 registered handsets and need to replace a handset. -OR• You wish to change the designated handset number of your registered handsets. You must first deregister ALL handsets, and then register each handset you wish to use again, one at a time. Please read carefully through all the instructions on this page before beginning the deregistration process. Deregister all handsets from the telephone base 1.
Appendix Alert tones and lights Handset alert tones One short beep Tone of each key press, if key tone is turned on. One long beep Indication to begin recording a message, memo or announcement. Two short beeps You are pressing qCID or pDIR on a cordless handset when the volume is already at its highest or lowest setting. -ORCall waiting tone. -ORError tone. Confirmation tone (three rising tones) The system has completed the command successfully.
Appendix Screen display messages Screen messages BASE 0 is calling The telephone base is calling. Call transferred You have transferred an outside call to another device. Caller ID log There are no entries in the caller ID history. empty Calling BASE 0 The handset is calling the telephone base (for intercom calls). Calling HANDSET X Call answered The handset or telephone base is calling another handset (for intercom calls). The telephone base is transferring an outside call to a handset.
Appendix Display screen messages Screen messages No answer. Try again The device(s) you are trying to transfer a call to is out of range, off hook, or has no power. No caller info The caller information is unavailable. Number already saved The telephone number you have entered is already in the directory. Not available at this time Someone else is already using the directory or caller ID history. No Incoming PTT Out of range OR No pwr at base The incoming PTT function is turned off.
Appendix Display screen messages Screen messages To register HS, see manual. Screen display before handset registration. To screen call, press [SELECT] Press MENU/SELECT to activate call screening. Unable to call. Line in use Failed phone call (the telephone line is in use). Unable to call. Try again You try to join a call when there are already four handsets on that call. XX Missed calls There are new calls in the caller ID history.
Appendix Troubleshooting If you have difficulty with your phone please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. My telephone doesn’t work at all. • Make sure the power cord is securely plugged in. • Make sure you plug the battery connector securely into the cordless handset. • Make sure you plug the telephone line cord securely and firmly into the telephone base and the telephone wall jack.
Appendix Troubleshooting I cannot dial out. • Try all the suggestions above. • Make sure you have a dial tone before dialing. The cordless handset may take a second or two to find the telephone base and produce a dial tone. This is normal. Wait an extra second before dialing. • Eliminate any background noise. Noise from a television, radio or other appliances may cause the phone to not dial out properly.
Appendix Troubleshooting The batteries do not hold a charge. • If the cordless handset is in the telephone base or charger and the charge light is not on, refer to The charge light is off or blinking (page 113). • Charge the battery in the cordless handset for at least ten hours. For optimum daily performance, return the cordless handset to the telephone base or charger when not in use. • If the battery is depleted, it may take approximately 30 minutes to charge the handset before it shows Low battery.
Appendix Troubleshooting I experience poor sound quality when using the handset speakerphone. • For increased sound quality while using the handset speakerphone, place the handset on a flat surface with the dial pad facing up. I hear other calls while using my phone. • Disconnect the telephone base from the telephone jack, and plug in a different telephone. If you still hear other calls, call your telephone service provider. My cordless handset does not ring when I receive a call.
Appendix Troubleshooting My calls cut in and out while I’m using my cordless handset. • Other electronic products such as HAM radios and other DECT phones can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices. • Do not install this phone near a microwave oven or on the same electrical outlet. You may experience decreased performance while the microwave oven is operating.
Appendix Troubleshooting My caller ID isn’t working. • Caller ID is a subscription service. You must subscribe to this service from your telephone service provider for this feature to work on your phone. • The caller may be calling from an area that supports caller ID. • Both your and your caller’s telephone service providers must use caller ID compatible equipment.
Appendix Troubleshooting System does not answer after the correct number of rings. • Make sure that the answering system is on. ANS ON should show on the handset and the /ANSWER ON light on the telephone base should be on. • If toll saver is activated, the number of rings changes to two when you have new messages stored (pages 85). • If the memory is full or the system is off, the system will answer after ten rings.
Appendix Troubleshooting • If you subscribe to voicemail service, change the number of rings so that your answering system answers before your voicemail answers (pages 85). To determine how many rings activate your voicemail, contact your telephone service provider. • If there is a fax machine connected to the same telephone line, try disconnecting the fax machine. If that solves the problem, consult your fax machine documentation for information on compatibility with answering systems.
Appendix Troubleshooting I subscribe to a nontraditional telephone service that uses my computer to establish connections, and my telephone doesn’t work. • Make sure your computer is powered on. • Make sure your Internet connection is working properly. • Make sure that the software is installed and running for your nontraditional telephone service. • If you are using a firewall, it may prevent access to your nontraditional telephone service provider. Contact your service provider for more information.
Appendix Maintenance Taking care of your telephone • Your cordless telephone contains sophisticated electronic parts, so you must treat it with care. • Avoid rough treatment. • Place the handset down gently. • Save the original packing materials to protect your telephone if you ever need to ship it. Avoid water • You can damage your telephone if it gets wet. Do not use the handset in the rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.
Appendix Important safety information This symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock. Safety information • • Read and understand all instructions in the user’s manual. Observe all markings on the product. • Do not use a telephone in the vicinity of a gas leak.
Appendix Important safety information Especially about cordless telephones • Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the handset by radio waves, so there is a possibility that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset.
Appendix Important safety information Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S.
Appendix FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your telephone service provider upon request.
Appendix FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Appendix Limited warranty The AT&T brand is used under license - any repair, replacement or warranty service, and all questions www.telephones.att.com or 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. about this product should be directed to our website at call 1.
Appendix Limited warranty 5. How do you get warranty service? www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. To obtain warranty service, visit our website at NOTE: Before calling for service, please review the user’s manual; a check of the PRODUCT’s controls and features may save you a service call.
Appendix Technical specifications RF frequency band 1921.536MHz - 1928.448MHz Channels 5 Operating temperature 32°F - 122°F 0°C - 50°C Telephone base voltage 96Vrms - 129Vrms (AC voltage, 60Hz) Telephone base voltage 6VDC @ 600mA (AC adapter output) 5.1VDC @ 1000mA Handset voltage 2.
Index Index A D Alert tones handset, 101 telephone base, 101 Announcement, 75 Answer an incoming call during an intercom call, 48 during PTT, 56 Answering calls, 34 Answering system, 75–96 Assign a speed dial number, 65 Auto off, 35 Day and time handset, 15 telephone base, 26 Delete a caller ID log entry, 72 a directory entry, 63 a speed dial number, 67 Dialing from a record in the caller ID history, 72 from the directory, 63 Directory dial a number, 63 edit entries, 64 name search, 62 new entries, 59 D
Index Index I P Important safety information, 116– 118 Installation, 7–12 Intercom, 46–49 Paging tone, 45 Phonebook, 58 Power adapter, 8 Predialing, 34 Push-to-talk, 50–57 L Last number redial, 36 LCD language, 16, 27 reset LCD language, 16, 27 Lights, 102 Limited warranty, 121–122 M Maintenance, 115 Make an outgoing call during PTT, 57 Making calls, 34 Memory match, 70 Message alert tone, 82 counter display, 94 playback, 88–91 Mute, 40 N Names enter into directory, 59 search, 62 Number of rings, 80
Index Index T Technical specifications, 123 Telephone base quick reference guide, 4–6 ringer tone, 25 ringer volume, 25 screen icons, 100 voicemail indicator, 29 Temporary ringer silencing, 35 Time handset, 15 telephone base, 26 Troubleshooting, 106–114 V Visual message waiting indicator handset, 18 telephone base, 29 Voice announce caller ID telephone base, 28 Voicemail, 18, 29, 84 quick access, 67 Voice prompts, 86 Volume control handset, 14, 39, 89 telephone base, 25, 39, 89 W Wall mount installation,
Remote access wallet card Use the wallet card below to help you remember commands to control your answering system from any touch-tone telephone. Cut along dotted line. Call your phone number, then enter your two-digit access code (preset to 19). Action Remote command 1 Play new messages................ 2 Delete the message............... 3 Delete all old messages...... 33 Repeat or go back.................. 4 Stop................................................ 5 Help menu.............................
www.telephones.att.com © 2013 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Printed in China. Issue 1 AT&T 01/13.
