User's Manual

Sound Detection and Auto Wake Up
Adjust Sound Detection Sensitivity
You can turn on Sound Detection Alert and adjust the Baby Unit’s Sound Sensitivity to only detect your
desired level of sounds. When the Baby Unit detects sounds that exceed the chosen level, the Parent
Viewer screen turns on if it has been switched off or dimmed, and the Baby Unit transmits the detected
sounds to the Parent Viewer. You will immediately be able to see and hear your baby.
If you have turned on Sound Detection Alert, the Parent Viewer beeps when the Baby Unit detects sounds.
Sound
Sensitivity
Level
Level 3 (Highest) Level 2 (Medium) Level 1 (Lowest)
Description
The Parent Viewer
screen and speaker turn
on for very small sounds,
including background
noises from your baby’s
room.
The Parent Viewer screen
and speaker turn on
for babbling and louder
sounds from your baby.
The Parent Viewer
remains quiet when your
baby makes soft sounds.
The Parent Viewer screen
and speaker turn on
only for loud crying or
screeching sounds from
your baby. The Parent
Viewer remains quiet
when your baby makes
soft sounds.
Sound Activated Screen and Audio - Auto Wake-Up
When Auto Wake-Up is turned on,
the Parent Viewer screen stays off
to save power when the Baby Unit
detects no sound.
Once the Baby Unit detects sounds
that are louder than the chosen
sound sensitivity level, the Parent
Viewer screen and speaker turn on
automatically. The Parent Viewer
will then turn off again after no
sound has been detected for a
while.
The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in
an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of
service within the United States and Canada. The program provides a convenient alternative to placing used
Li-ion batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the
program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY
®
for information
on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is
set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the
battery. The CEC battery charging testing mode is activated while charging. Even if the Parent Viewer is paired to Baby Units,
the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by
a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC
criteria. The Baby Unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8
in (20 cm) or more. The transmitter and antenna of the Parent Viewer shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The Baby Unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the Baby Unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-
102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC seal
California Energy Commission battery charging testing mode
FCC and IC regulations
Disclaimer and Limitation of Liability
LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook.
LeapFrog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of
this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a
result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect
against data loss.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN ICES-3 (B)/NMB-3(B)
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Warranty: Please visit our website at leapfrog.com for full details of the warranty provided in your country.
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de
l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les
risques d’incendie, d’électrocution et de blessures corporelles,
dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites
sur l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du nourrisson.
La supervision du nourrisson est la responsabilité du parent
ou de la personne qui s’occupe de l’enfant. Ce produit pourrait
cesser de fonctionner et, par conséquent, vous ne devriez pas
présumer qu’il continuera de fonctionner correctement pendant
une période de temps donnée. De plus, il ne s’agit pas d’un
instrument médical et ne devrait pas être utilisé comme tel. Ce
produit est destiné à vous aider à superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre
source d’humidité, par exemple, près d’une baignoire, cuve
à lessive, évier de cuisine, dans un sous-sol humide ni près
d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un
risque d’explosion pourrait survenir si un mauvais type de
pile est utilisé pour l’unité du parent. La pile ne peut pas être
soumise à des températures extrêmes élevées ou basses et à
une faible pression d’air à haute altitude pendant l’utilisation,
l’entreposage ou le transport. L’élimination de la pile dans le
feu ou dans un four chaud, ou l’écrasement ou le découpage
mécanique de la pile peuvent entraîner une explosion. Laisser
la pile dans un environnement à température extrêmement
élevée peut entraîner une explosion ou la fuite d’un liquide ou
d’un gaz inflammable. Une pile soumise à une pression d’air
extrêmement basse peut provoquer une explosion ou une
fuite de liquide ou de gaz inflammable. Éliminer la pile usagée
conformément aux informations du Sceau RBRC.
7. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension
serait inadéquate risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques :
Adaptateur de l’unité du parent : Sortie : 5V DC 2A
VTech Telecommunications Ltd.
Modèle: VT07EUS05200
Adaptateur de l’unité du bébé : Sortie : 5V DC 1.5A
VTech Telecommunications Ltd.
Modèle: VT07EUS05150
Informations sur les piles rechargeables :
Zhuhai Great Power Energy Co., Ltd.
Lithium battery, 3.7V 5000mAh;
Modèle : GSP806090-5Ah-3.7V-1S1P
8. Lorsqu’ils sont branchés dans une prise de courant, les
adaptateurs secteur ont été conçus pour être orientés
correctement, soit à la verticale ou au plancher. Les broches
n’ont pas été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE
COURANT, la prise de courant doit être installée près du
produit, afin d’assurer une accessibilité sécuritaire à la prise
de courant.
10. Débranchez ce produit de la prise de courant avant de
procéder au nettoyage. N’utilisez pas de nettoyants en
aérosols. Utilisez un chiffon humide pour le nettoyer.
11. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
12. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit
où l’on risque d’écraser le cordon d’alimentation ou de le
piétiner.
13. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur l’étiquette. Si vous ne connaissez
pas le type d’alimentation que vous possédez à votre
domicile, consultez votre marchand ou votre compagnie
locale d’électricité.
14. Ne surchargez pas les prises de courant murales ni les
rallonges électriques.
15. Ne placez pas cet appareil sur un chariot, meuble, trépied,
support de montage ni table chancelants.
16. Les trous et ouvertures du boîtier, situés à l’arrière de
l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour
l’empêcher de surchauffer, ne bloquez sous aucun prétexte
ces ouvertures et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou toute autre
surface similaire. De même, ne le positionnez pas à proximité
ni au-dessus d’une source de chaleur ou d’un calorifère. De
plus, ne placez pas l’appareil dans un endroit avant de vous
assurer qu’il y ait une bonne circulation d’air.
17. N’enfoncez jamais d’objets à travers les ouvertures de cet
appareil, car ils pourraient entrer en contact avec des points de
tension dangereux ou causer des courts-circuits qui peuvent
dégénérer en incendies ou en risques d’électrocution. Ne
renversez jamais de liquide dans ce produit.
18. Afin de réduire les risques d’électrocution, ne démontez
pas cet appareil, mais apportez-le dans un centre de service
autorisé. L’ouverture du boîtier ou le retrait de toutes pièces
que contient cet appareil, à l’exception de l’accès autorisé
à certaines portes ou ouvertures, risque de vous exposer à
des points de tension dangereux ou d’autres dangers. Un
remontage incorrect peut par la suite présenter des risques
d’électrocution.
19. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne sont
pas endommagées.
21. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés,
téléphones sans fils etc.). Pour l’éviter, s’assurer que le
produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité
de façon périodique, éteindre l’écoute-bébé quand il n’est
pas en cours d’utilisation.
22. Les enfants devraient être supervisés afin de vous assurer
qu’ils ne jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des personnes
(incluant des enfants) aux capacités physiques, sensorielles
ou mentales réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné suffisamment
de supervision ou d’instructions relativement à l’utilisation de
l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚
C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez
pas près d’une source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive
telle que la lumière du soleil ou au feu.
4. Avertissement - Risque de strangulation
- Les enfants se sont ÉTRANGLÉS dans des
cordons. Gardez ce cordon hors de portée des
enfants (à plus de 0,9 m). N’enlevez pas cette
étiquette.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du
parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)
portative avec un article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez
d’installer votre moniteur vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil, radios, téléphones
cellulaires, interphones, moniteurs, téléphones, ordinateurs
personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’,
une firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR recommande aux
médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens
qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de LeapFrog est conforme à toutes les normes se
rapportant aux champs électromagnétiques (EMF) standard. Si
vous le manipulez correctement en suivant les instructions de
ce guide, son utilisation sera sécuritaire pendant de nombreuses
années, selon les meilleures évidences scientifiques dont nous
disposons aujourd’hui.
For cETL compliance only
Night Light
Mount the baby unit on a dry wall (optional)
Night Vision (B&W and Color)
1. Place the wall mount bracket
on a wall and then use a
pencil to mark the top and
the bottom holes as shown.
Remove the wall mount
bracket and drill two holes in
the wall (7/32 inch drill bit).
Notes
• Check for reception strength and the Baby Unit’s viewing angle before drilling the holes.
• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the
screws and anchors separately to mount your Baby Units.
2. If you drill the holes into a stud, go
to step 3.
• If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with the
wall.
3. Align the wall mount
bracket and screws with
the holes in the wall as
shown. Tighten the screw
in the middle hole first,
so that the wall mount
bracket position is fixed.
You can tighten the other
screw in the top hole.
3. Insert the screws into
the holes and tighten
the screws until only 1/4
inch of the screws are
exposed.
4. Place the Baby Unit on
the wall mount bracket.
Tighten the screw into
the threaded socket at
the bottom to secure
the Baby Unit. Align
the holes on the wall
mount bracket with the
screws on the wall, and
slide the wall mount
bracket down until it
locks into place.
5. You can maximize your Baby Unit’s
viewing angles by tilting the wall mount
bracket.
Hold the Baby Unit, and then rotate
the knob in an anti-clockwise direction.
This will loosen the joint of the wall
mount bracket.
Tilt your Baby Unit up or down to adjust
to your preferred angle. Then, rotate
the knob in a clockwise direction to
tighten the joint and secure the angle.
OR
4. Place the Baby Unit on
the wall mount bracket.
Tighten the screw into
the threaded socket at
the bottom to secure
the Baby Unit.
1
2
Alert Icons
• Displays when Parent Viewer’s battery is low and
needs charging.
• Displays when motion is detected by Baby Unit.
• Displays when sound is detected by Baby Unit.
• Displays when the temperature detected by Baby
Unit exceeds the set maximum.
• Displays when the temperature detected by Baby
Unit is lower than the set minimum.
Notes:
• If you have muted the Parent Viewer speaker, only the Parent Viewer screen will turn on when a
sound is detected.
• If you have turned on Auto Wake Up but turned off Sound Detection Alert, the Parent Viewer will
wake up when the Baby Unit detects sounds that are louder than the chosen sound sensitivity level.
The Baby Unit has infrared LEDs that allow
you to see your baby clearly at night or in a
dark room. When the Baby Unit being viewed
detects low light levels, the infrared LEDs
switch on automatically. When Black and
White Night Vision mode is activated,
appears on the screen. When Color Night
Vision mode is activated,
appears on the
screen.
Notes
• It is normal to see a short white glare on your Parent
Viewer screen as the Baby Unit is adapting to the
dark environment.
• If you adjust the night vision mode while night vision
is not activated, the new settings will be saved and
applied the next time it activates.
Change your night vision viewing mode
1. Press the Night Mode quick set key
to view the Night Mode menu.
2. Press
or to choose for
black-and-white night vision viewing or
for color night vision viewing.
Parent Viewer Icons (continued)
Select Patrol mode as your monitoring
mode to alternately view the image from
Baby Units
and every 10
seconds.
Patrol mode
Select Split mode as your monitoring mode to view the images
from both Baby Units at once.
Note
• While in Split mode, you can press or to highlight the view of the Baby Unit 1
or Baby Unit 2
, and hear the sounds transmitted from the highlighted Baby Unit.
Split mode
Monitoring mode
Single CAM mode
Select Baby Unit 1 or Baby Unit 2 to
view the image from the selected Baby Unit.
The Parent Viewer display will dim to conserve energy after 5 minutes of inactivity, in which
there were neither any key pressed nor alert received from the Baby Unit.
Night Vision
Mode
Description
B&W Night Vision
Suitable for extremely dark or low
light environments.
Images will be in black-and-white.
Color Night Vision
Suitable for low-light room
conditions with night light as an
assisting light source.
Images will be in color.
Dim Mode
For LF915-2HD and Pairing with LF920-0HD Only
Motion Detection
Adjust Motion Detection Sensitivity
You can turn on Motion Alert and adjust the Baby Unit’s Motion Sensitivity to only detect
your desired level of motion. When the Baby Unit detects motions that exceed the chosen
level, the Parent Viewer screen turns on if it has been switched off or dimmed, and the Baby
Unit displays the live video feed. You will immediately be able to see and hear your baby.
If you have turned on Motion Alert, the Parent Viewer beeps when the Baby Unit detects movements.
Motion
Sensitivity
Level
Level 3 (Highest) Level 2 (Medium) Level 1 (Lowest)
Description
The Parent Viewer screen
and speaker turn on for
small motions, such as
yawning or stretching.
The Parent Viewer screen
and speaker turn on for
normal daily motions,
such as people walking
around the house.
The Parent Viewer screen
and speaker only turn on
for large motions, such
as children running or
jumping around.
Adjust the night light with the Parent Viewer
1. Press the Night Mode quick set key
to view the Night Mode menu.
2. Press
to brighten the night light (or turn on
the night light when it is switched off).
Press
to dim the night light (or turn off the
night light when it is at the lowest brightness
level).
1. Press
to enter the main menu.
2. Press
and to select
, press
.
3. Press
and to select
, press
.
4. Press
and to choose the desired
brightness level, then press
to confirm
your selection.
Want a softer hue from the Baby Unit’s night light to relax your little one? You can control the brightness
of its glow remotely from your Parent Viewer, or directly on the Baby Unit.
2
1
1
2
Visit our Consumer Support website 24 hours a day at:
U.S.: leapfrog.com/support
C.A.: leapfrog.ca/support
Or call our Customer Service number: 1 [phone] in the U.S. and Canada during Customer Service hours
Monday to Friday, 9am - 6pm Central Time
Adjust the night light with the Baby Unit
• Tap the Night light control key
located
on the top of the Baby Unit to turn on/off the
night light.
• Tap and hold the Night light control key
to adjust the night light’s brightness.
- OR -
Tip
• The video quality may vary depending on the
surrounding environment and interfering factors like
lightings, objects, colors and backgrounds. Adjust
the Baby Unit’s angle or place the Baby Unit at a
higher elevation to prevent glare and blurry displays.
Note
• If Auto Brightness has been pre-selected, any adjustment in night light brightness (either on the Baby Unit or
the Parent Viewer) will automatically turn off Auto Brightness mode and switch to the fixed level of brightness.
Troubleshooting
Symptom Try this
Why does the baby
monitor not respond
normally?
Try the following (in the order listed) for a common cure:
1. Disconnect the power to the the Baby Unit(s) and Parent Viewer.
2. Wait a few seconds before connecting power back to the Baby Unit(s) and Parent Viewer.
3. Turn on the Baby Unit(s) and the Parent Viewer.
4. Wait for the Parent Viewer to synchronize with the Baby Unit(s). Allow up to one minute
for this to take place.
Why doesn’t the Baby
Unit’s and Parent
Viewer’s power LED
turn on when I switch
on the units?
The Parent Viewer may not be connected to power. Insert the appliance plug into the power
jack of the Parent Viewer and put the adapter in a wall socket. Then, press the
Power
button on the Parent Viewer to establish connection with the Baby Unit.
The Baby Unit may not be connected to power. Insert the appliance plug into the power jack
of the Baby Unit and put the adapter in a wall socket. Then, slide the On/Off switch on the
Baby Unit to establish connection with the Parent Viewer.
Why doesn’t my
Parent Viewer charge
when connected to AC
power?
Make sure your power source is not controlled by a wall switch.
Why are my images in
black and white?
The images are in black white during night-time or in a dark room when night vision is
automatically activated. You can also choose to view your baby at night in color, see Night
Vision (B&W and Color) to learn how.
Why is the Baby Unit
producing a high-
pitched noise?
The Parent Viewer and Baby Unit(s) may be too close to each other.
• Move the Parent Viewer away from the Baby Unit(s) until the noise stops (OR)
• Turn down the volume of your Parent Viewer.
Why does the Parent
Viewer beep?
The Baby Unit(s) may be out of range. Move the Parent Viewer closer to the Baby Unit(s)
(but not less than 3 feet).
The Parent Viewer may not have enough battery for the Parent Viewer to perform normally.
Charge the Parent Viewer until the battery icon becomes solid
.
The temperature of your baby’s room may be too high or too low.
Why can’t I hear any
sounds from the Parent
Viewer? Why can’t I
hear my baby cry?
The Parent Viewer speaker volume may be too low or muted. Press
to open the volume
adjustment menu, then press
to increase the speaker volume. Or you can use the Parent
Viewer menu to change the Parent Viewer’s sound sensitivity to the highest level (level 5),
see Sound Detection and Auto Wake Up.
Why can’t I establish a
connection? Why does
my connection cut off
every now and then?
Why are there sound
interruptions?
The Baby Unit(s) may be out of range. Move the Parent Viewer closer to the Baby Unit(s)
(but not less than 3 feet).
Other electronic and wireless products may cause intereference with your baby monitor. Try
installing your baby monitor as far away from these devices as possible.
If you powered on only one Baby Unit but have two paired to the Parent Viewer, your Parent
Viewer may display
and the LINK LED light flashes. Switch to the Baby
Unit you have turned on via the menu.
Instructions for Care
FOR INDOOR, DRY-LOCATION USE ONLY.
To keep this product in good condition, follow these guidelines:
• Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors or
fluorescent lamps).
• Do not spill liquid of any kind on this product or
immerse the product in water as it may render it
inoperative.
• Clean with a slightly damp cloth in cold water (do not
use soap, detergent, or other chemicals).
• Keep food and beverages away from this product.
• Make sure the product is dry before you connect it to
the power source again.
• Never try to dismantle the unit.
• Avoid prolonged exposure to extreme temperatures
and direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
Customer Support
7
0
2
5
.5
°
C
7
0
25
.
5°
C
70
25.5°
C
25.5°C
25.5°C
70
25.
5
°
C
Specifications are subject to change without notice.
© 2021 LeapFrog Enterprises, Inc.
a subsidiary of VTech Holdings Limited.
All rights reserved. 07/21. LF915-XHD_QSG_V1.
5 minutes of inactivity
Press any button
10s
70
25.5°C
7
0
25
.
5°
C