User's Manual

Appendix
98
Troubleshooting
»¸¶»´Åº¸¿¼º»Ç¼ÆÂæ
f Make sure you plug the power and line cords in correctly and securely.
f Unplug the electrical power. Wait for 15 seconds, then plug it back in. Allow
up to one minute for the cordless handset and telephone base to reset.
f Clean the cordless handset, charger and telephone base charging contacts
each month with a pencil eraser or cloth.
f The battery may not be connected to the handset or is missing completely.
Ensure that the battery is installed properly.
My caller ID isn’t working.
f Caller ID is a subscription service. You must subscribe to this service from
your telephone service provider for this feature to work on your phone.
f The caller may not be calling from an area which supports caller ID.
f Both your and your caller’s telephone service providers must use caller ID
compatible equipment.
f If you subscribe to high-speed Internet service (DSL - digital subscriber
¿¼Á¸Ç»ÅÂȺ»ÌÂÈÅǸ¿¸Ã»ÂÁ¸¿¼Á¸ÌÂÈÀÈÆÇ¼ÁÆÇ´¿¿´¬¥è¿Ç¸Åµ¸Çʸ¸ÁÇ»¸
Ǹ¿¸Ã»ÂÁ¸¿¼Á¸¶ÂÅ·´Á·Ç»¸Ǹ¿¸Ã»ÂÁ¸Ê´¿¿½´¶¾ôº¸!»¸è¿Ç¸ÅßɸÁÇÆ
noise and caller ID problems resulting from DSL interference. Please contact
ÌÂÈÅ¬¥ƸÅɼ¶¸ÃÅÂɼ·¸Å¹ÂÅÀŸ¼Á¹ÂÅÀ´Ç¼ÂÁ´µÂÈÇ¬¥è¿Ç¸ÅÆ
System does not receive caller ID when on a call.
f Make sure you subscribe to caller ID with call waiting features from your
telephone service provider. Caller ID features works only if both you and
Ç»¸¶´¿¿¸Å´Å¸¼Á´Å¸´ÆÂæ¸Å¼Áº¶´¿¿¸Å¢ƸÅɼ¶¸´Á·¼¹µÂÇ»Ǹ¿¸Ã»ÂÁ¸
service providers use compatible equipment.
Incomplete messages.
f If a caller leaves a very long message, part of it may be lost when the
ÆÌÆǸÀ·¼Æ¶ÂÁÁ¸¶ÇÆÇ»¸¶´¿¿´ì¸ÅÇ»¸À´Ë¼ÀÈÀŸ¶ÂÅ·¼ÁºǼÀ¸ÌÂÈ
have set.
f If the caller pauses for longer than seven seconds, the system stops
recording and disconnects the call.
f If the system’s memory becomes full during a message, the system stops
recording and disconnects the call.
f ¢¹Ç»¸¶´¿¿¸ÅÔÆɼ¶¸¼ÆɸÅÌÆÂìÇ»¸ÆÌÆǸÀÀ´ÌÆÇÂÃŸ¶ÂÅ·¼Áº´Á·
disconnect the call.
¼ï¶È¿ÇÌ»¸´Å¼ÁºÀ¸ÆÆ´º¸Æ
f Press VOL S to increase the telephone base speaker volume.
f Press SDIR/VOLUME to adjust the message playback volume on a handset.