User's Manual

Specifications are subject to change without notice.
© 2016 VTech Communications, Inc. All rights reserved.
02/16. VM346_QSG_V1.0.
Basic operation - Parent unit Basic operation - Baby unit
"EKVTUTQFBLFSWPMVNF
Press     70-     to adjust your parent unit speaker
volume. It determines the volume of sound
transmitted from your baby unit.
63ē
ē
;PPN
Press to zoom in or out.
63
ē
6TFUIFNFOV
Press .&/64&-&$5 to enter the menu, choose
a menu item, or save a setting.
While in the menu:
Press
or to scroll up or down.
Press
to select an item, or save a setting.
Press
#"$, to return to the main menu or
idle screen.
•
•
•
Alert Tone
Low Battery Tone
No Link Alert
Sound alert in split-view
5VSOPGGUIFQBSFOUVOJU
Press and hold to power off your parent unit.
6U]KXOTMULL
6U]KXOTMULL
2s
5VSOPGGUIFTDSFFO
Press and hold -$%0/0'' to switch off
the screen. You can still hear sound from the
selected baby unit.
LCD is turning of
f...
2s
5BMLUPZPVSCBCZVOJU
Press and hold 5"-, and speak to your parent unit.
Your voice is transmitted to the baby unit.
63
ē
Long press
63ē
Overview - Parent unit
4UBOE
1PXFSKBDL
4QFBLFS
0OPGG
5"-,
;PPN
"OUFOOB
.JDSPQIPOF
-JHIUJOEJDBUPST
"SSPXLFZT
.&/6
   4&-&$5

   70-    
7*&8-$%0/0''
1"530-
41-*5
10s
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
03
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby monitor (optional)
03
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
NOT
E
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed. You
can tighten the other screw in the
top hole.
Place the baby unit on the wall
mount bracket. Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
The default angle of the wall mount bracket is 90 degrees. You
can maximize your baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Place the baby unit on the wall mount
bracket. Tighten the screw into the threaded
socket at the bottom to secure the baby
unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Change different views (require additional baby units - VM306)
You can view from different baby units if you have more than one baby units in your system
(7. purchased separately).
Press 7*&8 to switch between the images of the baby units.
Press 1"530- to alternately view the image from the baby units every 10 seconds.
Press 41-*5 to view the images from all baby units at once.
Press7*&8
Overview - Baby unit
*OGSBSFE-&%T
-JHIUTFOTPS
$BNFSB
0/0''MJHIU
/VOL/
Play/Stop
Microphone
4LJQ
5FNQFSBUVSF
TFOTPS
4QFBLFS
0/0''TMJEF
"EKVTUTQFBLFSWPMVNF
Press /VOL/ to adjust your baby unit speaker
volume. It determines the lullaby volume and
talkback volume transmitted from your parent unit.
5VSOPGGUIFCBCZVOJU
Slide the 0/0'' switch to 0'' to power off
your baby unit.
-VMMBCZ
Press / to play lullaby on the baby unit.
Press
to skip to the other lullabies.
Press
/ again to stop the lullaby.
•
•